DogWatch MB-2 Istruzioni per l'uso

Sfoglia online o scarica il pdf Istruzioni per l'uso per Prodotto per la cura degli animali domestici DogWatch MB-2. DogWatch MB-2 2.

Stampa la pagina

Troubleshooting

If your pet enters the signal field without responding to the correction signal, make sure that both the

transmitter and the receiver collar are "ON" and working. If both the transmitter and the receiver are

functioning properly, you may need to increase the signal range on the transmitter (or the wire) or

increase the correction level on the collar. Reminder: Never adjust the transmitter or the correction

level while your pet is wearing the receiver collar.

Receiver

•

Check to see if the transmitter is turned 'ON'.

•

Take the receiver collar off the dog and check the receiver by placing the test light on the

contact posts while holding the receiver next to your wireless transmitter or the boundary wire. If

your test light lights up, your receiver is working properly. Be sure not to touch the contact posts.

•

Make sure the collar fits and the contact points on the receiver actually touch your pet's skin.

•

Be sure the receiver battery is inserted correctly.

•

Replace the battery as needed. Average battery life varies depending on use.

Typical battery life is: R7 receiver = 6 months. R9 receiver = up to 2 years. SmartCollar = up to 1 year.

Transmitter

•

Check to see if the transmitter is plugged-in and turned "ON". If functioning properly, the Status

Light should be illuminated solid green (or blinking green depending on the Frequency setting.)

•

If using a wire, make sure the wire is properly connected and is separated to create a Signal

Field. Make sure the end is stripped and twisted together to create a continuous signal loop.

•

Check the Range Setting on the back of the transmitter. Increase the range if necessary. Too small

a signal field may allow your pet to get too close to the boundary area before receiving a warning.

2 Year Warranty

To see warranty information and submit Warranty Registration: www.dogwatch.com/support

REPLACEMENT BATTERIES AND COLLARS

Typical battery life is approximately 2 years but may

vary depending on use. For replacement batteries and

additional collars, contact your authorized DogWatch

Dealer or visit www.dogwatch.com/dogwatch-store

NOTE: The use of any battery other than a battery

authorized by DogWatch Inc., can cause erratic

operation of the receiver or could cause permanent

damage and may void the Warranty.

Modifications or changes to this equipment not expressly

approved by DogWatch, Inc., may void the user's authority

to operate the equipment.

7/64

(#36) drill

Wall Mount Guide

[2 places]

Cut template from the

booklet and tape to



wall to drill holes.

This device complies with part 15 of the FCC Rules and with Industry

Canada rules. Operation is subject to the following conditions: (1) This

device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may

cause undesired operation.

Le présent appareil est conforme à la partie 15 régles FCC et est

confirme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux conditions

suivantes: (1) l'apppareil ne doit pas produire de brouillage, et

(2) l'utilisateure de l'appariel doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

DogWatch products are lead-free and compliant with the

Reduction of Hazardous Substances (RoHS) initiative.

DogWatch Products are protected under U.S. Patent

numbers: 6,360,698; 6,467,435; and 6,825,768

If mounting to drywall

with no wall stud, be sure

to use the plastic anchors



provided.

The DogWatch

attached boundary wire.

How the System Works

The MB-2 transmits a silent radio signal that is recognized by a special receiver collar worn by your pet.

• When used without an attached boundary wire, the signal is transmitted a set distance from the

transmitter. The signal can be adjusted from 18 inches to 13 feet in diameter to create a pet-free

avoidance area.

• When used with a boundary wire, the signal comes from the wire. The wire may be installed to the

shape and size you need to create either an avoidance area (to keep your pet out of an area) or a

containment area (to keep your pet within an area).

At the edge of the signal, there is a warning zone. As your pet approaches the warning zone, the receiver

collar starts 'beeping' to alert your pet that he is too close to the boundary. With training (page 3), your

pet learns that if he goes beyond the warning zone, the beep is quickly followed by a 'correction' (an

unpleasant, but safe, sensation from the receiver collar). Your pet will learn to stay away from areas he

associates with the warning beep.

Status

Top

Light

Power

Bottom

Button

Controls

295104 Rev. A 12-20

DogWatch

Product Features and Operating Instructions

MB-2 is a dual function transmitter designed to be used either with or without an

Turning ON/OFF - Status Light

Press the Power Button to turn the unit ON. The Status Light will illuminate green

indicating the unit is ON. The green light indicates that the signal is being sent.

•

When using a boundary wire, the Status Light glows green only when there

is a continuous signal loop. See instructions on page 3.

Note: The green light may either be steady green or blinking green. This depends

on the Frequency setting of the transmitter.

Press the Power Button to turn the unit OFF. A red light will illuminate indicating

the unit is powering OFF.

Signal Range

Signal range is the distance the signal radiates from the transmitter or the

Wire

boundary wire.

Terminals

•

Turn the knob toward the 'Max' to increase the signal range.

This increases the size of the signal field.

•

Turn the knob toward the 'Min' to decrease the signal range.

This decreases the size of the signal field.

Never adjust the signal range while your pet is wearing the receiver collar.

Always test the signal field and mark the edge of the field with warning flags

before allowing your pet near the boundary area.

Frequency

This switch controls the broadcast frequency of the signal.

Do NOT change this setting. It is for DEALER USE ONLY.

NOTE: Do not set the transmitter on or near large metal objects.

MB-2