AsiaRF AW7615-NP1 Manuale - Pagina 8
Sfoglia online o scarica il pdf Manuale per Unità di controllo AsiaRF AW7615-NP1. AsiaRF AW7615-NP1 10.
Stampa la pagina
environment. This equipment should be installed and operated with minimum distance
the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
de rayonnement et votre corps.
The transmitter module may not be co-located with any other transmitter or antenna.
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not
possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection
d'autres canaux n'est pas possible.
This module is intended for OEM integrators under the following conditions:
1. Ensure that the end-user has no manual instructions to remove or install module.
2. This module is certified pursuant to Part 15 rules section 15.247, 15.407 and RSS-247.
3. This module has been approved to operate with the antenna types listed below, with the maximum
permissible gain indicated.
Frequency Band
2400-2483.5MHz;
5150-5850MHz
2400-2483.5MHz;
5150-5850MHz
2400-2483.5MHz
5150-5850MHz
2400-2483.5MHz;
5150-5850MHz
2400-2483.5MHz;
5150-5850MHz
4. Label and compliance information
Label of the end product:
FCC
The host product must be labeled in a visible area with the following " Contains FCC ID:
TKZAW7615NP1".
The end product shall bear the following 15.19 statement: This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
ISED
This transmitter module is authorized only for use in device where the antenna may be installed such
that
20
cm may be maintained between the antenna and users. The final end product must be labeled
in a visible area with the following: "Contains transmitter module IC: 9968A-AW7615NP1" or
"Contains IC: 9968A-AW7615NP1"
Contient le module d'émission IC: 9968A-AW7615NP1
The Host Model Number (HMN) must be indicated at any location on the exterior of the end product
or product packaging or product literature which shall be available with the end product or online.
5. Information on test modes and additional testing requirements
This module has been approved under stand-alone configuration.
OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.
The separate approval is required for all other operating configurations, including portable
1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C
Model Number
ANT010-DAU
A245005N
A2405N
A5005N
A245004
A245002
20cm
Antenna Type
PCB
PCB
PCB
PCB
Dipole
Dipole
www.asiarf.com
TEL: +886-2-29407880
FAX: +886-2-29407800
20cm
between
de distance entre la source
Gain(dBi)
2.4GHz: 5.2
5GH: 5.5
2.4GHz: 4
5GHz: 5.1
2.4GHz: 5.2
5GHz: 5
2.4GHz: 4
5GHz: 5.1
2.4GHz: 2
5GHz: 2
8