Ambient Technologies RCMT Istruzioni per l'installazione e il funzionamento - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per l'installazione e il funzionamento per Telecomando Ambient Technologies RCMT. Ambient Technologies RCMT 2. Manual on/off remote control with timer
Anche per Ambient Technologies RCMT: Manuale di installazione e istruzioni per l'uso (7 pagine)

Stampa la pagina

Ambient Technologies RCMT Istruzioni per l'installazione e il funzionamento

4. After reset the transmitter is operating in manual mode. The

room temperature is shown as above.

Manual Mode

1. Press the ON button once to turn on the appliance.

2. Press the OFF button to turn it off.

Timer Mode

1. Press the TIMER button once to start the timer, 90 min as shown

in the left Figure. Keep pressing the

TIMER button to set up timer to 60 or 30

min as desired. Three seconds later, the

tranmsitter will turn on the ﬁ replace.

2. Once the timer starts to count down to 0

min, the transmitter will send off signal

and turn off the ﬁ replace.

3. Press the OFF button to exit the timer mode and the transmitter

will shut off the ﬁ replace.

Backlight

The backlight color will change according to the current temperature

range. If the room temperature is over 78°F (26°C), then the back-

light will be Red. If room temperature is less than 61°F (16°C), the

backlight will be Green. Backlight will be Blue if the room tempera-

ture is between 61-78°F (16-26°C). When any key is pressed the

backlight will turn on for 8 seconds and then turn off.

Low Battery Detection

1. When the battery voltage of remote is less

than 3.4V, the low battery icon will ﬂ ash.

The battery will be checked every minute.

If the battery voltage of remote is less

than 3.2V, the remote will send the ﬂ ame

off command to the receiver and turn off

the ﬂ ame.

2. The transmitter will not operate with low batteries. Change the

battery before the battery is too weak for normal operation.

TURN THE UNIT OFF BEFORE REPLACING BATTERIES.

Child-Proof Protection

1. Press and hold ON and OFF buttons

simultaneously for 3 seconds to enter

child-proof mode.

2. The transmitter will not work until child-

proof mode is deactivated by pressing the

ON and OFF buttons simultaneously for 3

seconds again to exit child-proof mode.

Transmitter Thermal Shutdown

1. If transmitter measures a room temperature exceeding 99 de-

grees Fahrenheit, the LCD will display "HI" and the transmitter

will turn off the appliance.

2. Transmitter will not function until the

room temperature has dropped below 99

degree Fahrenheit.

3. If transmitter measures a room tempera-

ture less than 40 degrees Fahrenheit, the

LCD will display "LO" and NO SIGNAL will

be sent to turn on the appliance.

50D0103 RCMT.indd 2

Receiver

Low Battery Detection

When the battery voltage drops to a certain level, which is checked

once a minute, the low-battery LED will start to blink and the re-

ceiver will automatically turn off the appliance. The receiver will not

function again until fresh batteries are installed.

Slide Switch

1. ON position: the system will remain on until the slide switch is

placed in the OFF or RS position.

2. RS position: the system will only operate if the remote receiver

detects a signal from the transmitter.

3. OFF position: the system is off. The slide switch should be

placed in the OFF position if you will be away for an extended

period of time. If the remote receiver is mounted out of children's

reach, the OFF position also functions as a safety device by both

turning the system off and rendering the receiver inoperable.

TESTING YOUR NEW

REMOTE CONTROL SYSTEM

1. Connect the wiring terminal to the appliance. Refer to the appro-

priate Homeowner's Manual for proper wiring connections.

2. Light your gas appliance following the lighting instructions that

came with the appliance. Conﬁ rm that the pilot light is on; it must

be in operation for the remote control to operate the main gas

valve. Appliance pilot control knob must be in the ON position.

Appliance ON/OFF switch must be in OFF position.

3. Slide the 3 position button on the remote receiver to the ON posi-

tion. The main gas ﬂ ame should ignite.

4. Slide the button to OFF. The ﬂ ame should extinguish (the pilot

light will remain on).

5. Slide the button to RS (the center position), then press the ON

button on the transmitter to turn the system to ON. The main gas

ﬂ ame should ignite.

6. Press the OFF button on the transmitter to turn the system off.

The ﬂ ame should extinguish (the pilot light will remain on).

TROUBLESHOOTING

Symptom

Causes

Action

LED light on receiv-

Low battery

Check battery instal-

er blinking

lation and replace

batteries.

Appliance does not

1. Wiring/electrical

1. Slide the switch

come on.

connections faulty

to ON.If appliance

comes on, wiring

is not the cause. If

appliance does not

come, check wiring

connections.

2. DIP (Privacy)

2. Make sure the

switch setting on

transmitter and

transmitter does not

receiver have the

match receiver.

same DIP switch

settings.

3. Distance between

3. Make sure the

the transmitter and

operating distance is

receiver is more

less than 30 feet.

than 30 feet.

Receiver cannot

Receiver is installed

Make sure the

detect signal.

in an enclosure.

receiver is not

located inside a tight

enclosure.

WARNING: Changes or modiﬁ cations to this unit not

expressly approved by the party responsible for com-

pliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

•

Re-orient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for

help.

WARRANTY

This warranty gives you speciﬁ c legal rights and you may also have

other rights that vary from state to state or province to province.

Answers to any questions regarding our limited warranty may be

obtained by writing our corporate ofﬁ ces.

Ambient Technologies warrants each new Ambient Technologies

remote control against any defects that are due to faulty material or

workmanship to the original owner, for a period of ﬁ ve years after

the original date of purchase. This warranty and our liability does not

apply to batteries, nor does it include damage to merchandise or the

remote control resulting from accident, alteration, neglect, misuse,

improper installation or any other failure to follow Ambient Technolo-

gies installation and operating instructions.

Ambient Technologies agrees to repair or replace at its option any

Ambient Technologies remote control under warranty provided it is

returned postage prepaid to our warranty facility in a padded carton

within the warranty period, with proof of the original date of purchase

and a brief description of the malfunction. This limited warranty does

not include the cost of removal or re-installation. All Ambient returns

must have a return authorization number from Ambient Technical

Support.

149 Cleveland Drive

Paris, KY 40361

Technical Support: 800.398.6195

50D0103, Rev 3, 12/14

12/30/2014 9:05:50 AM