Ambient Technologies RTSC Istruzioni per l'installazione e il funzionamento - Pagina 2
Sfoglia online o scarica il pdf Istruzioni per l'installazione e il funzionamento per Telecomando Ambient Technologies RTSC. Ambient Technologies RTSC 2. Thermostatic flame height adjustment remote for signature command system
Stampa la paginaonly affects auto mode operation.
4. The default setting for transmitter is 2 (Medium), as shown
in the picture.
Low Battery Detection:
1. Battery voltage is checked once a
minute. When the battery voltage
drops to a certain level, the low-
battery icon will display on LCD,
and the transmitter will turn off
the appliance. The transmitter
will not function anymore until
fresh batteries are installed.
2. When the batteries are low, the
LCD displays a low battery indi-
cator. The low battery indicator
will be displayed in any mode.
3. The transmitter will not operate with low batteries. Change
the batteries before the batteries are too weak for normal
operation. TURN THE UNIT OFF BEFORE REPLAC-
ING BATTERIES.
Child-Proof Protection:
1. Press and hold the ON and OFF
buttons simultaneously for 3 sec-
onds to enter childproof mode as
shown in this picture.
2. The transmitter will not send a
signal again until childproof
mode is deactivated by pressing
the ON and OFF buttons simulta-
neously for 3 seconds to exit
childproof mode and the
Childproof indicator disappears from LCD.
Transmitter Thermal Shutdown:
1. If transmitter measures a room
temperature exceeding 99 degrees
Fahrenheit, the LCD will display
"HI" and the transmitter will turn
off the appliance.
2. Transmitter will not function until
the room temperature has
dropped below 99 degree
Fahrenheit. If transmitter meas-
ures a room temperature less than
40 degrees Fahrenheit, the LCD
will display "LO" and NO SIGNAL will be sent to turn
on the appliance.
Symptom
1. Battery icon on LCD on
transmitter.
2. LCD display is blank
3. LCD display shows
"funny" display
4. The receiver does not
respond to the
transmitter
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:
f i r e - p a r t s . c o m
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This warranty gives you specific legal rights and you may also
have other rights that vary from state to state or province to
province. Answers to any questions regarding our limited warran-
ty may be obtained by writing our corporate offices.
Ambient Technologies warrants each new Ambient Technologies
remote control against any defects that are due to faulty material
or workmanship to the original owner, for a period of five years
after the original date of purchase. This warranty and our liability
does not apply to batteries, nor does it include damage to mer-
chandise or the remote control resulting from accident, alteration,
neglect, misuse, improper installation or any other failure to fol-
low Ambient Technologies installation and operating instructions.
After contacting Ambient Technologies Tech Service to receive a
return authorization number, we agree to repair or replace at our
option any Ambient Technologies remote control under warranty.
Provided it is returned postage prepaid to our warranty facility in a
padded carton within the warranty period, with proof of the origi-
nal date of purchase and a brief description of the malfunction.
This limited warranty does not include the cost of removal or re-
installation.
TROUBLESHOOTING
Causes
Action
1. Low Battery
1. Replace batteries. Change
batteries every 6 months.
2. Check battery installation
or replace batteries.
3. Press Reset button at the
back of the transmitter.
1. Learning was not
1. Perform learning every
performed after
time after the DIP setting
resetting the Privacy
is changed
(DIP) switch setting
on transmitter
2. Transmitter measures
1. Move transmitter to a
temperature
cooler place and wait
exceeding 99 degrees
until temperature drops
Fahrenheit and
below 99 degree.
shows "HI" on LCD
3. Distance between the
1. Make sure the operating
transmitter and
distance is less than 30
receiver is more than
feet
30 feet
WARRANTY
Ambient Technologies
149 Cleveland Drive
Paris KY 40361
FOR TECHNICAL SUPPORT
CALL 800-398-6195
20H3181 Rel 1 Oct 2008