- ページ 9

ペットケア製品 Askoll PURE XL HC LEDのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Askoll PURE XL HC LED 14 ページ。 Marine aquarium kit
Askoll PURE XL HC LED にも：取扱説明書 (14 ページ)

ページを印刷する

1. Starting up the System

PURE Aquarium KIT

2) Switching-on of the day light at the switching-ON time set by the

user, with a progressive raising of the light intensity for about

30 minutes (the white and red LEDs become on; the blue LEDs

remain on).

3) Switching-off of the day light at the switching-OFF time set by

the user, with a progressive lowering of the light intensity for

about 30 minutes (the white and red LEDs switch off; the blue

LEDs remain on).

4) Complete switching-off of the blue actinic light 2 hours and 30

minutes after the switching-OFF time set by the user, with a

progressive lowering of the light intensity for about 30 minutes

(complete switching-off of the blue LEDs).

You can always turn the light on and off manually, even if the timer

is set to automatic mode.

The timer is equipped with a lock function to prevent accidental pres-

sure of the keys. Key locking is activated automatically after 3 min-

utes of inactivity. The locked status is signaled by the "bloc" message

that appears as soon as the block is activated and at each subse-

quent pressing of any keys. To remove the locked status and access

the timer functions, it is necessary to press the

quickly in sequence. Unlocking is confirmed by the appearance of

4 dashes on the clock digits for a few moments. If during the pro-

gramming phase the current time or the on/off times settings are not

completed, the lock will not activate after 3 minutes of key inactivity.

There is also a demo mode (DEMO), which simulates the complete

daily cycle in a few seconds to highlight the potential off the led

lighting system when controlled by the integrated timer (point F).

IMPORTANT

Turning the light off manually with the button

turning the light off automatically at the set time do not disconnect

the lighting unit from the power supply.

The PURE

aquarium timer does not need batteries. If there is a

LED

mains power failure, the system maintains the user settings for at

least 12 hours.

A. Setting the clock time on first start up (hours and

minutes)

Once the lighting unit is connected to the power supply, the timer

waits for the time to be set (it displays icon

digits flash).

1) Set the hour by pressing

setting. Then press

to set the minutes.

2) Set the minutes by pressing

the setting. Press

to confirm. The time has now been set.

If not any other programming operation is carried out, the lighting

system is pre-set to switch the day light on at 10:00 a.m. and switch

it off at 6:00 p.m. according to pre-set ramps. Therefore the blue light

will switch on at 08:00 a.m. and will switch off completely at 8:30 p.m.

To set the on/off times to your preference or to set the only manual

mode, refer to point C.

and

on the Timer and

and the two hour

to increase and

to decrease the

to increase and

to decrease

B. Manual mode

By pressing the key

day light (

icon on), the actinic blue light (

off the light completely.

C. Programming the automatic light on/off times

CAUTION: For a correct execution of the daily cycle, the time frame

between the switching-ON time and switching-OFF time set by the

user should not exceed 19 hours and 30 minutes.

1) Unlock the timer by pressing the

in sequence.

2) Hold down button

countdown 3..2..1  "light" to terminate).

3) The time digits will now display "Auto" and icons

flash. To set the only manual mode, press

displays. Confirm by pressing

4) Once you have set automatic mode "auto", icon

digits will flash. Set the on time (hour and minutes) in same way

keys

as for the clock time (points 1 and 2, par. A).

5) Once you have set the on time, icon

flash. Set the off time (hour and minutes) in same way as for the

clock time (points 1 and 2, par. A).

6) Once you have finished, the timer will display the clock time

again.

7) The timer is now programmed to run the automatic daily light

cycle, as indicated at the start of this chapter.

D. Changing the clock time (hours and minutes)

If you need to change the clock time, proceed as follows:

1) Unlock the timer by pressing the

in sequence.

2) Press and hold down

must wait for 2 countdowns to complete: 3..2..1  "light" 

3..2..1  "time").

3) The icon

and the hour digits will flash: set the clock time

(hours and minutes) as indicated in par. A.

E. Turning the RFT function on and off

The RFT is on by default (On). To turn it on/off, proceed as follows:

1) Unlock the timer by pressing the

in sequence.

2) Press and hold down

must wait for 3 countdowns to complete: 3..2..1  "light" 

3..2..1  "time"  3..2..1  "RFT").

3) The clock digits display "On" and icon

deactivate (OFF) or activate (ON) the RFT function. Confirm by

pressing

4) Once you have finished, the timer will display the clock time

again.

When the RFT function is on, the timer will flash every 15 days to

remind you to do scheduled maintenance. To reset the indication,

press

it is possible to switch on in sequence the

icon on) and to switch

and

until the text "light" displays (wait for the

until the text "man"

and the hour digits will

and

until the clock digits display "time" (you

and

until the clock digits display "RFT" (you

flashes; press

keys quickly

and

will

and the hour

keys quickly