- ページ 4

医療機器 AMD Lasers PICASSOのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。AMD Lasers PICASSO 17 ページ。
AMD Lasers PICASSO にも：クイック・スタート・マニュアル (8 ページ)

ページを印刷する

• Always press STANDBY on the control panel before exchanging handpieces or removing the fiber optic connector from the unit.

• Move the circuit breaker (located on rear panel) to the OFF (0) position, remove the key, and place it in a secure location

before leaving the unit unattended.

• Remove all obstructions from the cooling vents on the device to ensure proper air flow and cooling of the device.

Safety Classification

The following safety classifications are applicable to the Picasso & Picasso Lite devices:

• Laser Radiation: Class 4 (US classification)

• Type of electrical shock protection: Class 1 (US classification)

• Degree of electrical shock protection: Type B Applied Part

• Laser not protected against water ingress: Ordinary Equipment

• Not suitable for use in the presence of flammable anesthetic mixtures

• Operation Mode: See Specifications

Safety Questions

Please direct safety questions to an authorized representative or directly to AMD LASERS.

SAFETY FEATURES

Circuit Breaker

Serves as a line switch to separate the unit from the main power supply: 0 = OFF, | = ON.

System Monitor

The system monitors emergency stop switch, remote key, footswitch attachment, fiber attachment, and output power. Any detected

error will stop the system.

Keyswitch

The unit can only be switched ON (key in horizontal position) with the proper key. Always turn the unit OFF (vertical position) and

remove the key when not in use.

STANDBY/READY Button

Once the circuit breaker and keyswitch are set to the ON position, the STANDBY/READY button on the keypad must be pressed to

enable the footswitch. One beep will sound to indicate that the system is ready for use. The STANDBY/READY button on the Picasso

will turn green. For the Picasso Lite, the LED light will begin to blink.

Footswitch

No laser energy will be emitted until the user presses down on the footswitch.

Emergency Stop

Press the red Emergency Stop button to instantly turn off the unit. The button will be in the out position. To reset the Emergency Stop

button, simply press again. The button will be in the pushed in position for normal operation. Only use the Emergency Stop for

emergencies.

Remote Interlock

The remote interlock feature allows the user to connect the laser to an operatory door trigger to disable the laser when the door

is opened. Please consult a qualified electrician to perform the proper wiring from the Remote Interlock Connector/Plug to the

operatory door.

The remote interlock plug must be inserted for normal operation. If the laser is not connected to a remote interlock, an auxiliary

connector, which bridges the connector contact pins, must be inserted into the Remote Interlock socket, located at the back of the unit.

The connector is attached by pushing it into place. Removal is accomplished by sliding the portion of the connector closest to the

laser housing away from the laser. The display will show the two dashes in the lowest position until the user has cleared the offending

interlock violation (insertion of the supplied remote interlock plug and/or closing the door).

Audible and Visual Display

The laser will give an audible beep and flash a light within the ready button while the laser is firing. The audible sound may be

adjusted or muted by the user. The visual display may not be turned off.

Functional Display

The Light Emitting Diode (LED) indicators on the front of the unit and control panel show the functional conditions of the system.

Page 8

WIRELESS FOOT CONTROL COMPLIANCE

Mod.: PICASSO

FCC ID: YXI-PFCA

IC: 9348A-PFCA

FCC:

15.19 (a) (3):

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

15.21:

The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or

modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

15.105:

(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement,

placed in a prominent location in the text of the manual.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IC: RSS-GEN:

7.1.2 Transmitter Antenna

WARNING: Do not modify this equipment without written authorization of the manufacturer.

Canada Only: This device should be installed and operated in accordance with CAN/CSA-Z386-92: Laser Safety in Health Care

Facilities.

User manuals for transmitters shall display the following notice in a conspicuous location:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approval for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

7.1.3 User Manual

User manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location in the user

manual or alternatively on the device or both.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

For Canadian Users only. A cable back up has been provided for the operation of the foot pedal as a wireless foot pedal is not

currently available for use in Canada. Please be sure to connect the cable between the foot pedal and the "FS" socket on the back of

the unit, verify that battery is removed, and then start your unit.

Frequency: 2.4G Hz

Voltage:1.5 Volts DC

1.5V AA Alkaline Batteries Only

Page 9