おもちゃ Amdi PARTNER2のPDF インストラクションシートをオンラインで閲覧またはダウンロードできます。Amdi PARTNER2 2 ページ。 Augmentative communication devices
ページを印刷するA
PARTNER2™
UGMENTATIVE
INSTRUCTION SHEET
Congratulations on your purchase of the PARTNER2™ Entry-Level Communicator. T
A
UGMENTATIVE COMMUNICATOR THAT OFFERS HIGH QUALITY
. PARTNER2
PRICE
IS MANUFACTURED TO THE HIGHEST COMMERCIAL STANDARDS TO PROVIDE MANY YEARS OF RELIABLE OPERATION
PARTNER2'
FULLY GUARANTEE THE
D
F
PARTNER2
ISTINCTIVE
EATURES OF THE
D
,
ROP RESISTANT
W
ATER RESISTANCE FOR EASY CLEANING
T
HE SHATTERPROOF CASE IS MADE OF A HIGH IMPACT PLASTIC
L
IGHT WEIGHT AND PORTABLE
T
PARTNER2
HE
GIVES YOU
M
ESSAGES CAN BE STORED FOR UP TO
I
N ADDITION TO THE BUILT IN MICROPHONE
I
NTERCHANGEABLE
GENERAL OPERATION:
All controls are located on the back of the PARTNER2.
The PARTNER2 augmentative communicator is a self-contained communication device, which permits the user to record and playback 2
messages of 16 seconds in length. Graphic overlays (picture cards) can be easily changed by simply sliding the overlay between the housing grid
and the message square through the slot on the top of the grid. Simple to operate, just turn the unit on, adjust the volume, select and push the
picture to activate the corresponding message.
BATTERY INSTALLATION
1.
Make sure that the PARTNER2 is turned off. Set VOLUME control switch fully to the right, until it clicks off.
2.
Turn the PARTNER2 over and lay the front of the unit on a flat stable surface.
3.
To gain access to the battery compartment and expose the batteries, remove the two screws holding down the plastic battery
cover on the left side of the bottom of the unit.
4.
Remove the old batteries and discard them in accordance with your local recycling laws.
5.
Install the new batteries observing the proper polarity and using 4 new AAA batteries.
6.
Then replace the battery compartment cover by placing the cover over the access hole and tighten down the two screws. Insure
the battery cover is secure.
RECORD OPERATION:
Note: It is important during any recording operation that the built in microphone located at the back of the PARTNER2 is clear and
open.
1.
Turn the PARTNER2 ON. Turn the VOLUME control switch to the left, until it clicks ON.
2.
Set the VOLUME control, turning to the left, until it reaches the center of the range.
3.
Depress and hold the built-in recording button. The recording button must be engaged for the entire recording process.
4.
Select one of the 2 message squares on the face of the PARTNER2 and depress and hold down that message square, then begin
to say your message into the built-in microphone located at the back of the PARTNER2. For the best results, you should speak
directly into the microphone and be about 6 to 9 inches away from it in a quiet room.
5.
The remaining message square can be programmed in the same manner.
INPUT AND OUTPUT JACKS:
The Partner2 comes fully equipped with 2 external control jacks (see diagram – BACK VIEW), 1 - Input and 1 - Output. The two control jacks
on the back of the unit correspond to the two message squares on the front of the Partner2.
INPUT JACK:
The first jack labeled J1 on the back of the Partner2 is an Input jack (see diagram – BACK VIEW for jack
locations). It is for activating the first message square on the left. When the switch plugged into the Input
jack is activated, the message programmed into that message square will play.
OUTPUT JACK: The jack labeled J2 on the back of the Partner2 is an Output jack used to control low
voltage DC devices.
C
OMMUNICATION
,
S OPERATION FOR A FULL YEAR
ABLE TO WITHSTAND ROUGH HANDLING
.
(
2
.)
LESS THAN
LBS
"R
-V
"
EAL
OICE
HIGH QUALITY AUDIO REPRODUCTION
100
YEARS WITH NO POWER
,
SPEAKER AND RECORD SWITCH
O
,
M
VERLAYS
COMPATABLE WITH
AYER
*S
EE
D
EVICES
RELIABLE PERFORMANCE AND MANY IMPORTANT FEATURES FOR A VERY LOW
,
INCLUDING PARTS AND LABOR
.
.
.
.
, 1 OUTPUT
1 INPUT
AND
J
BOARDMAKER™ S
OHNSON
OFTWARE EXTEND USABILITY
W
ARRANTY AGREEMENT FOR DETAILS
PARTNER2
HE
IS AN ENTRY
. *
JACK IS PROVIDED FOR EXTERNAL HOOK UPS
.
.
-
LEVEL
. W
E
.