- ページ 3
配管製品 American Standard 3208.016.222のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。American Standard 3208.016.222 4 ページ。 Two-piece toilets with aquameter fill valve
ページを印刷する8
CAUTION: Overtightening of
COUPLING NUT could result in
breakage and potential flooding.
WATER INLET
WASHER
COUPLING NUT
VALVE NUT
TRIM PLATE
VALVE
CONNECT WATER SUPPLY
a.
Connect water supply line between
shutoff valve and tank water inlet
fitting.
Tighten COUPLING NUT 1/4 turn
beyond hand tight.
Check that refill tube
is inserted into overflow tube.
b.
Turn on supply valve and allow tank to
fill until float rises to shutoff position.
c.
Check for leakage at fittings, tighten or
correct as needed.
d.
Do not use plumber's putty to seal
these fittings.
Repair parts are determined by toilet tank number which can be found marked inside tank.
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
FOR 4094 ANTIQUITY, 4095 REPERTOIRE, AND
4094.702 WILLIAMSBURG
PART NO.
730288-XXX0A
TRIP LEVER
730535-XXX0A
TRIP LEVER (WILLIAMSBURG ONLY)
034783-XXX0A
BOLT CAP KIT (INCL 2 COVERS &
WASHERS)
738462-0070A
WATER CONTROL ASS'y W FLOAT BALL
738181-0070A
FLUSH VALVE
047158-0070A
COUPLING KIT, BOWL-TO-TANK
738258 -0070A
FLAPPER ASSEMBLY
11
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid
detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads
on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings
!
in the tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners
containing chlorine (calcium hypochlorite).
9
TANK
FLEXIBLE
SUPPLY
COMPRESSION
COLLAR
ADJUSTMENTS
a. Flush tank and check that tank fills and shuts off within 30 to 60 seconds, and
tank water level is set as specified on tank rear wall.
b. To adjust water level: turn water level adjustment screw counterclockwise to
raise level; turn adjustment screw clockwise to lower level.
c. To adjust flow rate (tank fill time): turn flow rate adjustment screw clockwise to
decrease flow rate (increase fill time); turn adjustment screw counterclockwise to
increase flow rate (decrease fill time).
d. Carefully position tank cover on tank.
e. The flush valve float has been factory set and does not require adjustments.
Repositioning of the float will change the amount of water used which may effect
the toilet's performance.
f.
If bowl fails to siphon, an adjustment may be required with the lift chain. Simply
remove the bead chain from the retainment clip (see Fig. 10A) and take up slack
on the chain, and reinsert on lift rod. Make sure the chain is not too taught.
DESCRIPTION
TO RAISE
WATER
LEVEL
+
TO LOWER
-
WATER
LEVEL
TRIP
LEVER
C L
WATER CONTROL
ASSEMBLY
WATER LINE
LEVEL
WATER INLET
FLUSH VALVE
FOR 4074.039 HERITAGE
PART NO.
730283-XXX0A
047227-XXX0A
738352-0070A
738181-0070A
047158-0070A
738258 -0070A
- 3 -
FLOW RATE
ADJUSTMENT
LIFT
OVERFLOW
ROD
TUBE
REFILL
TUBE
FLOAT
BALL
FLUSH
VALVE
FLOAT
FLAPPER
ASSEMBLY
DESCRIPTION
TRIP LEVER
BOLT CAP COVER PLATE KIT #207
WATER CONTROL ASS'y W FLOAT BALL
FLUSH VALVE
COUPLING KIT, BOWL-TO-TANK
FLAPPER ASSEMBLY
730489-1 00 Rev. B
FIG. 10A