- ページ 19

水システム Euro-Clear BlueSoft-K100-VR34のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Euro-Clear BlueSoft-K100-VR34 20 ページ。 Central household water softening devices with cabinets

ページを印刷する

Water purification and treatment equipment manufacturer and wholesale distributor

Tel: +36 96 544-240 • Fax: +36 96 544-248 • E-mail: [email protected] • Web: www. euro-clear.eu

Aid sheet for setting up

1. Check the mechanical and electical connections as follows:

1.1.

Is a mechanical protection filter built in front of the water softener?

1.2.

Is a pressure reducer built in front of the water softener?

Is the pressure of the raw water convenient? (2,5 – 6 bar)

1.3.

1.4.

Are the directions of water flow convenient? (on the montage block, on the device)

1.5.

Are the outlet of the softening rinsing water and the gravitation overflow of the brine tank

connected separately onto the channel?

1.6.

Is the electricity input right? (230V, 50HZ)

1.7.

Has the hardness of the raw water been measured?

If yes, the measured hardness is:

2.Program the control head of the water softening device

2.1.

Have the exact date and time been set?

2.2.

Setting the time for regeneration or the quality

2.2 1.

Regeneration mode selection:

Recommended time 02

2.2.2.

In case the device is quantity controlled, has the water quantity been set (in m

between the two regenerations?

If yes, it has been set up to:

For example.: in case of a device type BlueSoft 70 and raw water of 20 German hardness

It must be set up to: 70 / 20 = 3,5 m

Setting up time for washing (advanced settings)

2.3..1

Has backwash been set up?

Recommended minutes

2.3.2

Brine Draw

( based on table on page 23 )

2..3.3

Has refill been set up?

water quantity=litres of resinX0,8 (litre). Table on page 23

2.3 .4

Has time for rinse been set up?

After times for washing (setting up phases of regeneration), fill the cabinet with the right quantity of

water. Resin litres X 0,8 = L, for example 25 L resin X 0,8 = 20 L water

Start a manual regeneration with button

3. Starting manual regeneration, checking function cycles:

3.1.

Backwash (water gets onto the channel intensively).

Is everything all right with the function cycle?

3.2.

Brine absorption (little water comes out into the channel, the cabinet is running out of

brine).

Is everything all right with the function cycle?

3.3.

Water refill into the cabinet. Is everything all right with the function cycle?

4.4.

Backwash (onto a channel of higher volume of water flow)

4. After finishing regeneration, check the hardness of the water coming down from the device.

Without back mix, is the hardness of the water made by the device lower than 1 gh?

5. Set the water hardness up to at least 5 Gh in compliance with the regulation of the government

201/2001.

(The device can make water of lower German hardness, too.)

Possibilities of setting up hardness:

On the montage block or helped with by-pass valve on the control head.

Water hardness that has been set up:

6. Filling up the cabinet with tablets of salt. Recommended quantity 0,5 – 1 sack.

7. Train the staff handling the device.

8.Filling in the warranty document

9. Sending back the data sheet of setting up filled in and signed (terms of warranty) to the address below.

Euro-Clear Magyarország Ltd.

Mailing address: 9071 Gönyű, Kossuth Lajos street 65/A

E-mail:

[email protected]

Fax: +36 96 / 544 248

BlueSoft Household Water Softener

Euro-Clear Ltd.

A-02

A-01

2 minutes (based on table on page 23)

has time been set up?

....... G H

(Meter immediately)

Meter delayed quantity

Yes



for



.... .. m



2 - 2 minutes

3 –minutes



4 – minutes



5 – minutes



...........GH



Page 19.