- ページ 4

トイレ American Standard CADET 3 FloWise 2235のPDF 取り付け説明書お手入れとメンテナンスをオンラインで閲覧またはダウンロードできます。American Standard CADET 3 FloWise 2235 4 ページ。 Two-piece toilet

ページを印刷する

LIFT ARM

FIRST

IMPORTANT: Always clear

sand and rust from system.

• Make sure water supply is

off. Remove valve TOP by

lifting arm and rotating top

and arm 1/8 turn

counterclockwise, pressing

down slightly on cap.

Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall

not be responsible or liable for any damages caused by products used with Fluidmaster valves that were

not manufactured by Fluidmaster, Inc.

See Step 10 For Diagram

Problem

Possible Cause

Does not

a. Water supply valve closed.

flush

b. Supply line blocked.

c. Flush valve chain too loose or disconnected.

d. Sand or debris lodged in water control.

Poor or

a. Bowl water level too low.

sluggish

flush

b. Supply valve partly closed.

c. Partially clogged trapway and/or drain pipe

and/or vent.

d. Supply pressure too low.

Toilet leaks

a. Poor supply line connection.

b. Poor bowl to tank/floor connection.

Toilet does

a. Flapper seal leaking or deformed.

not shut off

b. Sand or debris lodged in water control.

c. Flush valve chain too tight, holding

flapper open.

Toilet bowl

a. Wax ring not fully compressed.

rocks after

b. Floor not level.

installation

In the United States:

American Standard Brands

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Consumer Affairs

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 442-1902

www.americanstandard-us.com

• While holding a container

over the uncapped VALVE

to prevent splashing, turn

water supply on and off a

few times. Leave water

supply off.

Troubleshooting Guide

FOR REPAIR PARTS LIST, SEE UNDER TANK LID.

• Replace TOP by engaging

lugs and rotating 1/8 turn

clockwise. MAKE CERTAIN

TIP IS TURNED TO THE

LOCKED POSITION. VALVE

MAY NOT TURN ON IF TOP

IS NOT FULLY TURNED TO

THE LOCKED POSITION.

Corrective Action

a. Open valve and allow water to fill tank.

b. Shut off water supply, disconnect supply line and inspect all gaskets

and washers. Reassemble.

c. Readjust chain length as required.

d. Shut off water supply. Remove cap and clean as per Fluidmaster

maintenance instructions at:

www.americanstandard-us.com/enews/fluidmasterguide.pdf

a. Check that refill tube is connected to water control and

inserted into overflow tube without being kinked or damaged.

b. Open supply valve fully. Be sure that proper supply tube size is used.

c. Remove obstruction. Consult a plumber if necessary.

d. Normal supply pressure must be at least 20 psi.

a. Review Step 8 of installation procedure.

b. Review Step 1 through 6 of installation procedure.

a. Clean debris from seal surface. Replace flapper seal as needed.

b. Shut off water supply. Remove cap and clean as per Fluidmaster

maintenance instructions at:

www.americanstandard-us.com/enews/fluidmasterguide.pdf

c. Readjust chain length as needed.

a. Retighten bowl-to-floor knobs.

b. Use toilet shims and /or place a bead of caulk around the base of

the toilet.

In Canada:

AS Canada ULC

5900 Avebury Rd.

Mississauga, Ontario

Canada L5R 3M3

Toll Free: (800) 387-0369

www.americanstandard.ca

- 4 -

TROUBLESHOOTING

IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK

SLOWLY, repeat Step 13.

IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF

NON-USE, it is a signal you are wasting water because:

• The end of the refill tube is inserted into overflow pipe, below

water level in tank. Attach refill tube to overflow pipe using "S"

clip provided.

• The flush valve is leaking because it's worn, dirty or

misaligned with tank ball or flapper (replace with a new flapper).

IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF

TANK WATER IS SLOW after valve has been in use for some

time, Fluidmaster Model 242 Replacement Seal may be needed.

Go to our website at www.fluidmaster.com for more solutions

to toilet problems.

For troubleshooting information please contact:

30800 Rancho Viejo Road

San Juan Capistrano, CA 92675

(949) 728-2000 (800) 631-2011

www.fluidmaster.com

® Registered trademark of Fluidmaster, Inc.

In Mexico:

Customer Service Manager

AS Maquila, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

www.americanstandard.com.mx

73092 8- 100 Rev. Q