- ページ 3

コントローラー Ekinex EK-FE1-TPのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Ekinex EK-FE1-TP 4 ページ。 Binary output 8-fold / blind actuator 4-fold

ページを印刷する

EK-FE1-TP

8xD.O. 16(10)A/230Vac

4xBlind 16(10)A/230Vac

230V~ 50/60Hz

bus KNX

KNX

bus

Connection of the KNX bus network and 230 Vac power supply

Connection of the loads

The connection of the controlled loads (fig. b, fig. c) is

made with the screw terminals located at the top. In case

the device is used as 4-fold blind actuator, the terminals

must be connected coupling the channels as follows: 1A-

1B, 2A-2B, 3A-3B, 4A-4B.

Characteristics of the terminals

• screw clamping of conductors

• maximum cross section of conductor 2.5 mm² (single-

wire) or 1.5 mm² (multi-wire)

• recommended wire stripping approx. 6 mm

• torque max 0.8 Nm

Connection of the loads (device used as 8-fold binary output)

3 1A

5 2A

11 1B

13 2B

Connection of the loads (device used as 4-fold blind actuator)

50/60 Hz

230 Vac

50/60 Hz

7 3A

9 4A

15 3B

17 4B

Warning! Sockets controlled via bus must be cle-

arly identified. Controlling loads with mobile installa-

tion (e.g. household appliances connected to mains

sockets) must be planned and realized with a care-

ful evaluation of the risks that may arise in the case

of control without direct visual contact with the load

(remote control). Connecting loads different than

those planned, remote controlling without direct ve-

rification of the current conditions of the connected

load or automatic controlling based on scenes or

time-scheduling can cause serious damage to pe-

ople and objects.

Use as a blind actuator

The output contacts for the up / down directions are in-

terlocked so that no voltage is applied simultaneously on

both contacts.

Warning! The electrical connection of the device

can be carried out only by qualified personnel. The

incorrect installation may result in electric shock or

fire. Before making the electrical connections, make

sure the power supply has been turned off.

Configuration and commissioning

Configuration and commissioning of the device require

the use of the ETS

V4 or later releases. These activities must be carried out

according to the design of the building automation system

done by a qualified planner.

Note. The configuration and commissioning of KNX

devices require specialized skills. To acquire these

skills, you should attend the workshops at KNX cer-

tified training centers.

Configuration

For the configuration of the device parameters the corre-

sponding application program or the whole ekinex

duct database must be loaded in the ETS program. For

detailed information on configuration options, refer to the

application manual of the device available on the website

www.ekinex.com

Product

code

EK-FE1-TP

APEKFE1TP##.knxprod

Commissioning

For commissioning the device the following activities are

required:

• make the electrical connections as described above;

• turn on the bus power supply;

• switch the device operation to the programming mode

by pressing the programming pushbutton located on

the front side of the housing. In this mode of operation,

the programming LED is turned on;

• download into the device the physical address and the

configuration with the ETS

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED is turned off. Now the bus device is

programmed and ready for use.

(Engineering Tool Software) program

Application

Communica-

program

tion objects

(## = release)

(max nr.)

222

program.

pro-

Group

adresses

(max nr.)

254