- ページ 3

スイッチ Ekinex EK-E12-TP-RW-NFのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Ekinex EK-E12-TP-RW-NF 9 ページ。 Pushbutton
Ekinex EK-E12-TP-RW-NF にも：データシート (5 ページ)

ページを印刷する

Mounting with frame

a) 1-fold square plate, with a 60 x 60 mm window

b) Rockers

c) Fixing screws (for device)

d) Device (pushbutton 71 Series)

e) Adapter for mounting with frame (included in the delivery)

f) Frame (square, Form or Flank Series)

g) Fixing screws (for metallic support)

h) Metallic mounting support

i) Flush-mounting box

Mounting without frame ('NF Series), version for round

box

Carry out the following steps:

• insert the metallic support (f) on the adapter (g);

• fix adapter and support (f+g) with the pair of screws

(e) on the flush-mounting box (h) equipped with fixing

holes at 60 mm distance;

• enter the bus terminal block, previously connected to

the bus cable in its slot on the rear side (see also: "Con-

nection of the KNX bus line"). At this point it is recom-

mended to carry out the commissioning of the device

(see also "Configuration and commissioning") or at le-

ast the download of the physical address;

• insert the pushbutton (d) on the metallic support (f);

• fasten the device on the metallic support supplied with

the pair of screws (c);

• snap the plate (a);

• snap the rockers (b) for the operation of the device.

Mounting without frame

a) 1-fold square plate, with a 60 x 60 mm window

b) Rockers

c) Fixing screws (for device)

d) Device (pushbutton 71 Series, 'NF version)

e) Fixing screws (for metallic support)

f) Metallic mounting support

g) Adapter for 'NF Series (included in the delivery)

h) Flush-mounting box

Mounting, version for rectangular box

Carry out the following steps:

• insert the metallic support (f) on the adapter (g);

• only for the versions which require a frame: snap a rec-

tangular frame (h) of the Form or Flank Series, inserting

it from the rear of support-adapter (f+g);

• fix adapter-support (f+g) (and the possible frame, d)

with the screws (e) on a flush-mounting box (i) provided

with suitable fixing holes (83,5 mm holes distance);

• insert the bus terminal, previously connected to the bus

cable, in its slot on the rear side (see also: "Connection

of the KNX bus line"). At this point it is recommended

to carry out the commissioning of the pushbutton (see

also "Configuration and commissioning") or at least the

download of the physical address;

• insert pushbutton (d) in the support-adapter (f+g).

Mounting the pushbutton follow the indication TOP (ar-

row tip pointing up) on the front side of the device;

• tighten the pushbutton in the support-adapter (f+g) with

the two screws (c);

• snap the rectangular plate (a);

• snap the rockers (b) for operating the device.

a) Plate (rectangular, with 60 x 60 mm window)

b) Rockers

c) Screws (for device)

d) Device

e) Screws (for metallic support)

f) Metallic support

g) Plastic adapter

h) Rectangular frame (not for 'NF versions)

i) Flush-mounting box (not delivered by EKINEX)

Note. The screws supplied in the package are su-

itable for standard installations. For more specific

applications, where the screws have to be replaced,

only flat-head screws must be used.

If necessary, the metal support for mounting on the wall

box can be ordered separately, with code EK-S71. For

mounting the pushbutton in combination with a double

plate, refer to the instructions delivered in the plate packa-

ge.