QUICK START INSTALLATION GUIDE
1
Unpack the box
Remove the components and system controller from the box. Save the
packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
(B)
• Power supply
• Magnetic mount TX antenna with 12' cable
• USB Flash drive
• Installation and Operation Manual
3
Choose your location
a.
Locate the system controller in an area with a network drop, or run
an Ethernet data cable to the unit from a network switch or hub.
b.
Choose a location for your magnetic mount TX antenna either
outside or inside at the highest central location in your facility.
Note: The TX antenna must be located at least 4' away from the system
controller and must always point up or down, never horizontal. The cable
length cannot be extended.
4 ft
minimum
TX Ant signal
out to clocks
4
Connect cables to the system controller
a.
Connect a CAT 5 or higher Ethernet patch cable (not
included) to the ETHERNET RJ45 port
b.
Connect the System Controller power supply to the POWER INPUT port
c.
Connect the magnetic mount TX antenna to the TX ANT port
*Lightning arrestor must be grounded per local electrical code.
d.
Plug 110v cord into power source. Turn the POWER SWITCH
on the back of the system controller to the on position.
Note: If your system controller supports more than one time sync option, refer to
the SiteSync IQ Installation & Operation Manual for detailed instructions.
(C)
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
GPS=Y
System controller located
high & central with Ethernet
drop for time reference
(A)
.
C
B
A
To local
power
(110vac)
SITESYNC IQ
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
a.
PRESS 1 to start the Setup Wizard (Page 10 in Installation Manual).
Create a 4 digit User Lock or enter 0000 to disable this feature. PRESS O.
b.
(B)
.
c.
Create a 4 digit Service Lock (for advanced features) or
(C)
.
enter 0000 to disable this feature. PRESS O.
d.
Select local time zone by using
the <> keys. PRESS O.
USET=Eastern, USCT=Central
USMT=Mountain, USPT=Pacific
Note: There are 40 options to choose from (Appendix B in Installation Manual).
e.
PRESS 8 to select automatic DST (Daylight Saving Time) or 0
to disable DST if your location doesn't observe DST. PRESS O.
PRESS 1 for 12-hour mode - AM/PM (1:00PM).
f.
PRESS 2 for 24-hour mode - Military (13:00).
g.
PRESS 1 to Enable DHCP or Press 2 to Disable DHCP. PRESS O.
h.
Use the keypad to enter the Unit IP Address. PRESS O.
i.
Enter the Subnet Mask. PRESS O.
j.
Enter the Gateway IP. PRESS O.
k.
Enter the DNS IP. PRESS O.
l.
PRESS 1 to use a Manual IP, or PRESS 2 for
a DNS IP Time Server. PRESS O.
• If 1 Manual IP, enter Time Server Address and
PRESS O to accept. Repeat for Alternative Time Server.
• If 2 DNS IP, PRESS O.
Note: this value can only be changed in Remote Connect.
O
m. Press
to accept the default (80) Port Number
n.
To confirm proper set up, press
• If successful, "Ethernet Sync Successful" will display.
• If not successful, "Ethernet Sync Failed" will display. Refer to the
troubleshooting guide in manual.
o.
"Setup Wizard Successfully Completed" will display.
6
Select Clock Code (for existing wired clock systems)
Continue on to Step 7 if you are not connecting wired clock circuits.
a.
Reference Appendix I in the manual for clock codes and wiring information
if you have wired circuits. Clock Code 01 is set from the factory. If 01 is the
code required, skip to 7 – Verify Unit is Transmitting. If the code needs to be
changed continue to next step.
PRESS P6 and enter your service lock to access the Configuration
b.
Menu. From the Config Menu, PRESS 3. This feature is used to set the
clock code for wired clock circuits. Enter the clock code using the keypad,
or choose 00 if you want to disable the clock code feature. Press O.
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
Note: Screen will
advance immediately
Skip if
1
is selected
in step g.
8
to sync.
ページを印刷する