- ページ 3

産業機器 Donovan Quick-Flip III 1808912のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Donovan Quick-Flip III 1808912 20 ページ。 Electric conversion

ページを印刷する

P/N 1808922 Rev. C

MESSAGE TO OWNERS

Thank you for buying this tarping system from Shur-Co

ate your confidence in our products. Please read and thoroughly un-

derstand this manual before installing and/or operating this system.

Pay particular attention to important safety and operating instructions,

as well as warnings and cautions. The hazard symbol

alert users to potentially hazardous conditions and is followed by cau-

tion, warning or danger messages.

Failure to READ AND FOLLOW INSTRUCTIONS could result in fail-

ure of your tarping system and/or personal injury. Your trailer require-

ments may, however, call for minor variations to these instructions.

Please inspect your tarping system periodically repairing or replacing

worn or damaged parts.

QUESTIONS? CALL OUR HELP LINE:

1-800-327-8287

MON-FRI 8 AM-5 PM EASTERN TIME

We at Shur-Co

are concerned with your safety and the safety of all

those operating this system. Therefore, we have provided safety de-

cals at various locations on your tarping system. Keep decals as clean

as possible at all times. Replace any decal that has become worn

or damaged, painted over or otherwise difficult to read. Replacement

decals are available.

SAFETY INSTRUCTIONS

1. Always wear safety glasses during installa-

tion and operation.

2. Stay clear of moving parts.

3. Do not operate under low-hung power lines.

Always check for overhead obstructions be-

fore opening or closing.

4. Open and close tarp only at job site.

5. Place safety decals in visible locations. Re-

place worn or damaged decals.

6. No other use of this system is authorized,

except as designed.

RUST PREVENTION

To prevent rust, paint all exposed metal, such as weld seams and/or

metal exposed by grinding or cutting, with corrosion-resistant paint.

. We appreci-

SAFETY

Hardware Identification ....................................................................... 1

Remove Spring-Loaded Housing from Base Assembly ...................... 2

is used to

Install New Housing ............................................................................ 3

Spring Pivot Installation - Tandem Axle Hydraulic Base Assembly ..4-5

Pivot Arm Installation - Tandem/Multi Axle Trucks .............................. 6

Tarp Tube Assembly & Tarp Installation .............................................. 7

Pre-Load Springs ................................................................................ 8

Electric Installation .........................................................................9-10

Pivot Arm Rest Installation ................................................................ 11

Replacement Parts ......................................................................12-15

Wrenches - 1/2", 5/16", 9/16", 5/8", 3/4", 7/8"

Ratcheting Socket Wrench

Sockets - 1/2", 9/16", 3/4"

Allen Wrenches - 1/8", 5/32", 3/16"

Drill Bits (metal cutting) - 5/16", 3/8", 1/2", 3/16"

Center Punch

Hammer

Tape Measure

Flat Head or Phillips Screwdriver

10. Grinder

11. Air or Electric Impact Driver w/9/16" Socket

12. Metal Saw

13. Steel Welder

14. Hex Driver Bit - 5/16"

15. Phillips Driver Bit - #2

16. Breaker Bar or Ratcheting Socket Wrench - 3/4"

• Spray all bearings and drive chain with penetrating oil as needed.

• Brush springs with steel brush weekly to remove dirt and spray with

penetrating oil.

• Tighten any loose bolts.

• Replace damaged/bent parts.

• Replace worn or broken springs.

• Replace/repair worn or damaged tarps.

Quick-Flip™ III Electric Conversion

TOOLS REQUIRED

MAINTENANCE

- ページ 3

TABLE OF CONTENTS