- ページ 14

ドア開閉システム DoorHan PCB-SWのPDF プログラミング説明書をオンラインで閲覧またはダウンロードできます。DoorHan PCB-SW 20 ページ。 Control board
DoorHan PCB-SW にも：プログラミング説明書 (20 ページ)

ページを印刷する

2. OPERATOR PROGRAMMING

2.1. BASIC PROGRAMMING

To perform basic programming do the following:

1. Enter the basic programming menu by pressing the «P» button. The left part of display will show «P», and the right part

will show the menu item according to the programming table (see Basic Programming table).

2. Pressing the buttons «+» or «-» select the required menu item.

3. To enter the menu press «P», the value of adjusted parameter will start flashing on the display.

4. Pressing the buttons «+» or «-» change the value of the adjusted parameter.

5. Press «P» to save new value and exit to main menu.

6. Having performed the adjustment of all the required parameters press «R» to exit the programming menu.

NOTE:

Press «R» if you need to exit to main menu without saving the parameters.

Display

Function

Operation mode:

Y — operation on time; n — operation on limit switches

Delay of 1st leaf closing:

1 — 1 sec; 2 — 5 sec; 3 — 10 sec; 4 — 15 sec; 5 — 20 sec; 6 — 25 sec; 7 — 30 sec; 8 — 35 sec;

9 — 40 sec

Delay of 2nd leaf opening:

1 — 1 sec; 2 — 2 sec; 3 — 3 sec; 4 — 4 sec; 5 — 5 sec

Control board setting (force, deceleration and operation time)

Automatic gate closing:

0 — off; 1 — in 10 sec; 2 — in 20 sec; 3 — in 30 sec; 4 — in 60 sec; 5 — in 90 sec; 6 — in 120 sec; 7 — in 180

sec; 8 — in 360 sec; 9 — in 420 sec

Auxiliary lighting (19-20 terminals):

0 — flashing during closing, solid during opening.

Switching on during any gate movement and switching off after stopping: 1 — in 10 sec; 2 — in 20 sec; 3 — in 30

sec; 4 — in 60 sec; 5 — in 90 sec; 6 — in 120 sec; 7 — in 180 sec; 8 — in 360 sec

9 — traffic light mode is activated only in the open position on the limit switches (does not work without limit

switches)

Cycles counter (one division means 1000 cycles)

2.2. OPERATOR SETTING

Learning process depends on the selected operation mode («P0» menu item).

Operation on limit switches:

1. Close the gate and lock the drives (if the ledge is available, adjust the leaves deceleration).

2. Enter the Basic Programming menu (see Basic Programming section) and select «P3» item.

3. Press the «P» button. The leaf 1 will start to open and the display will show blinking «Ln».

4. If you want to adjust deceleration, press the «+» button while the leaf moves.

5. After closing/opening cycle two short beeps will sound and the program will automatically exit the programming mode.

Operation on time (default):

1. Close the gate and lock the drives (if the ledge is available, adjust the leaves deceleration).

2. Enter the Basic Programming menu (see Basic Programming section) and select «P3» item.

3. Press the «P» button. The leaf 1 will start to open and the display will show blinking «Ln».

4. Press the «+» button and leaf 1 will start to slow down.

5. Press the «+» button once more and leaf 1 will stop. If single-leaf gate operation mode is set (see Advanced Programming

section), performing of item 12 will start.

6. Leaf 2 will start to open.

7. Press the «+» button and leaf 2 will start to slow down.

8. Press the «+» button once more and leaf 2 will stop.

OPERATOR PROGRAMMING

Defaul