- ページ 2
ゲートオープナー DoorKing 9150 SeriesのPDF クイックスタートをオンラインで閲覧またはダウンロードできます。DoorKing 9150 Series 2 ページ。 High voltage kit
DoorKing 9150 Series にも: マニュアル (5 ページ)
QUICKSTART "BASIC" GUIDELINES FOR MODEL 9150 - DIP-SWITCH AND WIRING REFERENCE
Model 9150 is intended for installation only on sliding gates used for vehicles.
Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the Installation/Owner's manual.
SW 1
Switch
Function
Setting
Changes the direction the operator will open/close the gate depending on the different chain configurations.
Front
1
Opening
Opening
Mount
direction
direction
using ON
using OFF
setting.
setting.
OFF
Auto-Close
2
Timer
ON
Motor
OFF
3
Hold
ON
4-OFF
5-OFF
Relay Activation
and
4-OFF
5-ON
4 and 5
LED Indicator
4-ON
5-OFF
Light Activation
4-ON
5-ON
SW 1
OFF
6
Self-Test
ON
7-OFF
8-OFF
Gate Open
7-OFF
8-ON
7 and 8
Back-Off
7-ON
8-OFF
Position
7-ON
8-ON
Note: After a DIP-switch setting is changed, power must be turned OFF and then turned back on for the new setting to take affect.
SW 2
Switch
Function
Setting
Exit Loop Port
OFF
Jumper Wire
Needed
Output
1
See Manual
ON
Full Open Input
OFF
Reverses Gate
2
ON
Stops Gate
Partial Open
OFF
3
(14 Ft)
ON
OFF
Built-in
4
Solenoid
Lock
ON
OFF
Operator Model
5
Select
ON
OFF
SW 2
Quick-Close
6
ON
Timer Override
7-OFF
8-OFF
Gate Close
7-OFF
8-ON
7 and 8
Back-Off
7-ON
8-OFF
Position
7-ON
8-ON
Description
Center or
All Rear
Opening
Opening
Opens
direction
Post
direction
Mounts
with
Mounts
Left
using OFF
using ON
setting.
setting.
OFF
setting.
Auto-close timer is OFF. Manual input required to close gate.
Auto-close timer is ON. Adjustable from 1-23 seconds to close gate.
Normal Setting. No voltage to motor when gate is stopped (Level gate).
Voltage applied to motor always. Keeps inclined gate from coasting when stopped.
Relay activates and LED is ON when the gate is fully open.
Relay activates and LED is ON when the gate is not closed.
Relay activates and LED is ON when the gate is opening and open.
Relay activates and LED is ON when the gate is opening and closing.
Normal Setting.
Runs self-test. Caution: Bench testing ONLY!
Normal Setting. Gate fully opens.
Gate stops short 1" from full open position. Used for a reversing edge device.
Gate stops short 2" from full open position. Used for a reversing edge device.
Gate stops short 3" from full open position. Used for a reversing edge device.
Description
A plug-in exit loop detector plugged into the EXIT Loop port will partially open single
operator or fully open dual operators depending on type of loop detector used).
Normal Setting. Plug-in exit loop detector will fully open gate (Single operator).
Normal Setting. Input to terminal #6 and/or reverse loops will reverse gate
during close cycle.
Input to terminal #6 and/or reverse loops will stop gate during close cycle – gate
will continue to close after input to terminal #6 and/or reverse loops are cleared
(Helps prevent tailgating vehicles from unauthorized entry).
Normal Setting. Switch must be OFF for terminal #5 input to open gate 14 Ft.
DO NOT use ON setting. NOT associated with partial open feature for the 9150.
Normal Setting. Fail-safe logic. Lock engages only if attempt is made to force gate
open (Factory setup).
Fail-secure logic. Lock engages after each gate cycle (2600-865 Lock kit required).
Normal Setting. Switch must be OFF for Model 9150.
DO NOT use ON setting for Model 9150.
Normal Setting. Timer will function normally.
Opening gate will stop and begin to close as soon as all reversing inputs (Reverse
loops, photo sensors) are cleared regardless of the distance the gate has opened.
Normal Setting. Gate fully closes.
Gate stops short 1" from full close position. Used for a reversing edge device.
Gate stops short 2" from full close position. Used for a reversing edge device.
Gate stops short 3" from full close position. Used for a reversing edge device.
Important:
Controls intended for user activation must be located at least six (6) feet away from any moving part
of the gate and where the user is prevented from reaching over, under, around or through the gate to operate the
controls. Emergency access controls only accessible by authorized personnel (e.g., fire, police, EMS) may be
placed at any location in the line-of-sight of the gate.
All Rear
Opens
Mounts
with
Right
ON
setting.
Com
Fire Box
#2-Full Open
#4-Connected device fully opens gate.
#5-Connected device opens gate 14-feet.
Telephone
Entry
External Entrapment
Protection Devices
Close Beam
Key Switch
Closed Gate
At least ONE external
entrapment protection
device MUST be installed
or the operator will NOT
Stand-Alone
Keypad
Connect ONLY MONITORED
Stand-Alone
Card Reader
Note:
All stand-alone
and telephone
entry devices
IMPORTANT:
Photo sensors
must use a
must use Normally Closed (NC)
separate power
contacts with the beam set for
source.
light operate (relay activated
when beam is not obstructed).
3-Wire Radio Receiver
Relay -
#2 - Full Open.
#5 - Opens gate 14-feet.
Com
24 volt
250 mamp.
max.
W A
R N
IN
G
E
REV
ERS
P
LOO
SER
MO
VIN
IOU
G
GA
Oper
S INJ
TE
CA
and
free
ate
gate
UR
Y OR
N
CA
or
Do
not
peop
of
only
le
when
US
DEA
E
ate
oper
allow
child
and
obst
gate
area
TH
path
Do
stand
not
gate.
to
ren
ructi
ons.
is
in
sight
Read
while
gate
gate
in
play
in
gate
EXIT
P
OPE
N
ER
owne
is
mov
path
area
LOO
TIM
r's
man
ing.
or
walk
and
ual
throu
gh
CH
safet
y instr
KEY
SWIT
uctio
ns.
CON
ANS
FOR
CAN
I/UL
MS
-325
TO
NG
/CSA
CER
TIFI
DOO
2-01
RKI
0
VEH
ICU
C22
.2
ED
TO
460
CLA
LAR
NO.
247
53382
SS
GAT
E OPE
1
MOD
EL
RAT
3
2
ERS
VITY
E
SER
HP
OR
4
REV
SEN
SITI
VOL
IAL
5
TS
SW2
AMP
SW1
MAX
S
PHA
GAT
E LOA
SE
Door
D
Hz
60
NC
King
, Inc.,
NO
Ingle
woo
d,
CA
3-Button
Control Station
DoorKing ONLY
Red Full Open
Green Close
White Com
IMPORTANT:
Only 1 monitored Device can be connected
to each input. An OPTIONAL Expansion Kit (sold
separately) will allow connection for additional devices.
Wall
Open Edge
Filler Post If necessary
Open Beam
UL 325 Terminal
N.C.
function.
1 - OPEN Beam STOP
2 - Ground (Common)
N.C.
3 - CLOSE Beam REVERSE
4 - Ground (Common)
5 - 24 VAC 250 ma. Max
6 - Ground (Common)
N.C.
7 - OPEN Edge/Beam REVERSE
Devices
N.C.
8 - Ground (Common)
N.C.
9 - CLOSE Edge/Beam REVERSE
10 - Ground (Common)
UL 325 DIP-Switches
DIP-switches MUST be turned ON for each device wired to terminal.
1 - OPEN Beam (UL 325 Terminal 1)
2 - CLOSE Beam (UL 325 Terminal 3)
3 - OPEN Edge (UL 325 Terminal 7)
4 - CLOSE Edge (UL 325 Terminal 9)
(See Installation/Owner's manual for more information)
Com
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
24 Volt - 250 mamp. max.
Relay N.O. - #2 - Full Open.
#5 - Opens gate 14-feet.
4-Wire
Relay Com
Receiver
24 Volt Com
1
Common
2
Full Open
EXIT
LOOP
3
24 V Power
FULL OPEN
FULL
ULL
4
Full Open
OPEN
TIMER
5
Partial Open
6
7
8
SW3
DOORKING
UL 325
9
4602-010
DIP-Switches
10
1
2
11
3
4
12
5
6
13
7
14
8
9
15
10
UL 325
16
SW1
SW2
Terminal
NC
NC
17
NO
18
Common
#5 Terminal Note (Single
Operator Only): Any opening
device connected to terminal #5 will
open the gate to the partial open
SW 2,
14-ft setting. External entrapment
switch 3
protection devices will also open the
must be
gate to the partial open setting. If the
OFF.
Inherent Reverse Sensor gets
activated during the close cycle, it
SW 2
will always fully open the gate.