レシーバー DoorKing MicroCLIK 8057 SeriesのPDF マニュアルをオンラインで閲覧またはダウンロードできます。DoorKing MicroCLIK 8057 Series 3 ページ。 Rf receiver

MODEL 8057 MicroCLIK

The model 8057 RF Receiver is designed for use with MicroCLIK™ transmitters. The receiver can store 10 facility codes and 50 to

16,000 unique transmitter codes depending on the model selected. It is also programmed to recognize only certain transmitter

buttons.

The 8057 has a built in programming keypad allowing transmitter codes to be block coded or individually added/deleted to its

memory. It is a stand alone receiver that activates a built-in dry contact form "C" relay when a programmed transmitter code is

received. The received code MUST match the programmed "Facility Code", "Transmitter Code", and "Transmitter Button Code"

before the receiver relay will activate.

The MicroCLIK™ system is compatible with

the HomeLink system found in many

automobiles.

Installation

This receiver is NOT designed to be installed outdoors without being protected from the weather. An outdoor enclosure is available for the receiver

if required (P/N 8057-110 - Metal Outdoor Box).

Install the 8057 receiver in a location so the antenna is NOT surrounded by metal and is in free air as high as possible above the ground.

A longer Coax Antenna kit is available for the receiver if required (P/N 1514-073 - Includes antenna, mounting "L" bracket and 15 feet of coax

cable).

The RF LED on the side of the case will blink as RF energy is received. If the LED blinks or is on continuously, this indicates that there may be

interference on the frequency (318 MHz) and short range may be the result. If this happens, try relocating the receiver or remove the source of

interference.

Note: Loop detectors and proximity card readers can cause receiver interference.

M a

s t e

( S e

r C

e n

o d

e x t

e B

p a g

u t t

e )

o n

Receiver Terminal Wiring

Stand-Alone Power and Device Wiring :

terminals #1 and #2. Use minimum 18 AWG wire to power the receiver.

12-24 Volt

Transformer

• If DC power is used (Transformer): Terminal #1 is NEGATIVE and Terminal #2 is POSITIVE.

• Connect the receiver relay contacts to the device to be activated.

- Receiver Terminal #3 is the relay contact Normally OPEN (N.O.)

- Receiver Terminal #4 is the relay contact Normally CLOSED (N.C.)

- Receiver Terminal #5 is the relay contact Common (C).

Gate Operator:

Connect the

3 wires from the gate operator

as indicated.

™

P/N 8066-080

Removable receiver

terminal for easy wiring.

v e r

c e i

n a

R e

m i

T e r

#1 - Input Power

#2 - Input Power

#3 - Relay Contact (Normally Open)

#4 - Relay Contact (Normally Closed)

#5 - Relay Contact (Common)

#6-8 - Not Used

DC Polarity Matters!

To Receiver Terminal #1 (Neg.)

To Receiver Terminal #2 (Pos.)

From "Low Voltage Common"

From "Circuit Board" Power

From "Radio Open"

RF RECEIVER

P/N 8067-080

MicroCLIK™ Transmitters

12-24 Volt AC, 12-24 Volt DC (Negative)

12-24 Volt AC, 12-24 Volt DC (Positive)

Terminals 3-4-5

rated for 30 volt,

1 amp max.

Connect 12 - 24 Volt AC or DC power to

To Receiver Terminal #1

To Receiver Terminal #2

To Receiver Terminal #3

P/N 8068-080

R F

L E

F Connector

Coax Antenna Kit

(Included)

18" Coax Cable

120 S. Glasgow Avenue

Inglewood, California 90301

DoorKing Part Numbers

8057-081

50 Transmitter Codes

8057-082

100 Transmitter Codes

8057-083

250 Transmitter Codes

8057-084

500 Transmitter Codes

8057-085

1000 Transmitter Codes

8057-086

5000 Transmitter Codes

8057-088

16,000 Transmitter Codes

U.S.A.