- ページ 3
ガレージドアオープナー DOORWORKS GDC6のPDF 取付説明書および取扱説明書をオンラインで閲覧またはダウンロードできます。DOORWORKS GDC6 20 ページ。 Overhead door operator
Read and Follow These Important Safety Instructions
You will see Warning and Caution statements on the following Pages.
Read and follow these safety instructions carefully. Failure to do so could result in serious personal injury or death.
Warming
Caution
means that severe injury or death may result from failure to follow instructions
means that property damage or injury may result from failure to follow instructions
Be sure to read and follow all instructions carefully.
To reduce the risk of electric shock, this equipment has a grounding type plug, that has a third (grounding) pin.
This plug will only fit into a grounding type outlet. If the Plug does not fit into the outlet, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Check to make sure the garage door is properly installed and balanced. Garage door & parts are under
extreme tension and under no circumstance should you attempt to adjust on your own. Have a qualified
garage door service person make repairs to cables, spring and other hardware before installing the opener.
Install Entrapment Warning Label next to control button. Read the Control Adjustment Warning Label. Instal
Emergency Release Tag to the Emergency Release Cord. Mount the Emergency Release Knob 180cm from the
fioor. Use the manual release only to disengage the trolley. Do not use the Red Release Cord and Knob to pull
door up or down. If possible, use the Emergency Release only when the door is closed.
Do not connect opener to power source untilinstructed. Install door opener 210cm or more above floor.
After instaling opener, the door must reverse when it comes in contact with a Scm high object. Check this safety
feature often.
REMOVE ALL ROPES CONNECTED TO THE GARAGE DOOR.
DISENGAGE ALL EXISTING GARAGE DOOR LOCKS TO AVOID DAMAGE TO THE GARAGE DOOR.
Fiberglass, aluminum and steel doors must be reinforced to prevent damage. Consult with manufacturer for
recommendations.
All installation and wiring must be done in strict compliance with local and state building and electrical codes.
Connect the power cord to a properly grounded outlet only. Do not in any way alter or remove the grounding pin.
Photo Eye System must be installed properly. Operators recommend Photo Eye System is installed on every
garage door
for
your
added
protection. Opening
doors
must not close and
Closing
doors must open
once
the
beam is broken. See the test procedure page 16.
Locate push button within sight of garage door, away from all moving parts and out of reach of chidren (minimum|
150cm above floor). To reduce the risk of injury to persons, use this operator only with a sectional door.
Never operate the opener if the system is not operating properly.
Always
disconnect electric power before
making repairs
or
removing
cover.
Activate
opener
only
when the door is in full view and free from obstructions.
No one should enter or leave the garage while the door is moving. Do not allow children to play near, or operate
the door.
Keep
the
remote control
away from children.
After Installation is complete fasten this manual near the garage door. Perfom periodic safety checks and
recommended maintenance and adjustments.
NEVER G UNDER A STOPPED, PARTIALLY OPEN DOOR
Test door opener monthly. The garage door MUST reverse on contact with a 5cm high object (or a two by 4 board
laid flat) on the floor. After adjusting either the force or the limit of travel, retest the door opener. Failure to adjust
the opener
properly
increases the risk of
severe
injury
or
death.
For products having an emergency release, when possible, use the emergency release only when the door is
ciosed Use caution when using this release with the door open. Weak or broken springs are capable of
increasing
the
rate of
door
closure and
increasing
the risk of
severe
injury
or
death.
KEEP GARAGE DOORS PROPERLY BALANCED. See owner's manual. An improperly balanced door increases
the risk of severe injury or death Have a qualified service person make repairs to cables, spring assemblies, and
other hardware
SAVE THESE INSTRUCTIONS