電動工具 Astro Pneumatic 600PTのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Astro Pneumatic 600PT 2 ページ。 Pistol grip punch / flange tool with 5.5mm punch
ページを印刷するModel:
Foreseen Use of the Tool
Do not use the tool outside of the design intent.
Never modify the tool for any other purpose, or for its use.
Safety Precaution
Caution: To help prevent personal injury
•
Normal use of this product is likely to expose
the user to dust and/or microscopic particles
containing chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm. Always wear
appropriate safety equipment and clothing when
using this product. Study, understand and follow
all instructions provided with this product.
•
Always wear ANSI approved goggles when using
this product.
•
Always select the correct accessories of the
correct size and design for the job that you are
attempting to perform.
•
Always work in a clean, safe, well-lit, organized
and adequately equipped area.
•
Do not begin repairs without assurance that
vehicle is in secure position, and will not move
during repair.
PRODUCT INFORMATION
• Punch designed for easy replacement
• Performs hole punching and panel crimping
• Features a rotating head for convenient use
• Every pull of the lever delivers a single punch or a
single flange crimp with precision control
• Forms an offset crimped edge on sheet metals for
no-bump lap welds
• Lightweight, yet ruggedly built
• Cuts metal fabrication time in half
Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in
a safe accessible place.
600PT
Product Type:
PISTOL GRIP PUNCH/FLANGE TOOL
WITH 5.5MM PUNCH
www.astrotools.com
1 YEAR LIMITED WARRANTY
•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year from the date of 1st use.
Astro reserves the right to determine whether the product failed because of defective
material, workmanship or other causes and to charge back for missing parts. Astro
Pneumatic Tool Co., at its discretion, will repair products covered under this warranty
free of charge. The original user is to return the product (with the exceptions listed
below) with the distributor's name, address, adequate proof of date of purchase or a
copy of warranty card, and a short note explaining the problem. Failures caused
by accident, alteration, or misuse are not covered by this warranty.
•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user
and may not be transferred to subsequent owners.
•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
P.O. Box 251935
Los Angeles, CA 90025
PLEASE DO NOT RETURN ANY PRODUCT TO THE P.O. BOX.
CALL 1-800-221-9705 FOR INSTRUCTIONS.
Unpacking
When unpacking, check the parts diagram and part number listing
on page 2 to make sure all parts are included. If any parts are
missing or damage, please call your distributor.
PISTOL GRIP PUNCH/FLANGE TOOL
WITH 5.5MM PUNCH
Specifications:
7/32" (5.5mm)
Punch Capacity:
5/32" (4mm)
Piston Stroke:
7-1/2" (191mm)
Overall Length:
2-1/4lbs. (1.0kg)
Net Weight:
1/4"
Air Inlet Thread NPT:
3/8" (10mm)
Air Hose I.D. Size:
4cfm
Avg. Air Consumpt.:
90-120psi
Air Pressure:
1