レシーバー Flying Industry Development S2UB-DC24-ANT2のPDF クイックマニュアルをオンラインで閲覧またはダウンロードできます。Flying Industry Development S2UB-DC24-ANT2 4 ページ。 Rf wireless receiver

ページを印刷する
RF Wireless Receiver (Model 0020535)
Feature:
Wireless control, easy to install
Relay output, can control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110-240V or DC
0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through
walls, floors and doors.
With characteristics of reverse power protection and over current protection
Use an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
You can use one transmitter to control several receivers, such as each two buttons on transmitter controls one receiver. They can pair different model
transmitters, includes model CV-4 (500M), CV-6 (500M), CV-8 (500M), CV-12 (500M) and CB-4 (1000M), CB-6 (1000M), CB-8 (1000M), CB-12
(1000M), etc... For example, you can use one 4 buttons transmitter CV-4 or CB-4 to control two receivers, use one 6 buttons transmitter CV-6 or CB-6
to control three receivers, use one 8 buttons transmitter CV-8 or CB-8 to control four receivers, use one 12 buttons transmitter CV-12 or CB-12 to
control six receivers, etc...
Receiver Parameters:
Model No.: S2UB-DC06-ANT2 / S2UB-DC09-ANT2 / S2UB-DC12-ANT2 / S2UB-DC24-ANT2
Power Supply (Operating Voltage): DC6V (S2UB-DC06-ANT2), DC12V±1V (S2UB-DC12-ANT2), DC9V±1V (S2UB-DC09-ANT2), DC24V±2V
(S2UB-DC24-ANT2)
Working Frequency: 315MHz / 433MHz
Channel: 2 CH
Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Maximum Working Current of Relay: 10A / each channel
Static Current: ≤6mA
PCB size: 67mm x 50mm x 18mm
Case size: 75mm x 54mm x 27mm
Work with Fixed code transmitters.
External Extend Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 150cm
Weight: 35g
Anti-interference, waterproof, shielded wire set inside
Magnetic stand design for easy to install
Usage (with the transmitter like CV-12 or CB-12):
Connect DC power to terminal "+" and "-".
Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals A and B are Normally Closed.
Setting different control modes (We have set the receiver as Toggle mode before delivery. If you want to use other modes, do as following):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle: Press -> On; Press again -> Off.
Press button 1: Turn on relay 1 of Receiver 1 (connect B and C, disconnect A and B)
Press button 1 again: Turn off relay 1 of Receiver 1 (disconnect B and C, connect A and B)
Press button 2: Turn on relay 2 of Receiver 1 (connect B and C, disconnect A and B)
Press button 2 again: Turn off relay 2 of Receiver 1 (disconnect B and C, connect A and B)
...
Press button 11: Turn on relay 1 of Receiver 6 (connect B and C, disconnect A and B)
Press button 11 again: Turn off relay 1 of Receiver 6 (disconnect B and C, connect A and B)
Press button 12: Turn on relay 2 of Receiver 6 (connect B and C, disconnect A and B)
Press button 12 again: Turn off relay 2 of Receiver 6 (disconnect B and C, connect A and B)
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on relay 1 of Receiver 1 (connect B and C, disconnect A and B)
Release button 1: Turn off relay 1 of Receiver 1 (disconnect B and C, connect A and B)
Press and hold button 2: Turn on relay 2 of Receiver 1 (connect B and C, disconnect A and B)
Release button 2: Turn off relay 2 of Receiver 1 (disconnect B and C, connect A and B)
...
Press and hold button 11: Turn on relay 1 of Receiver 6 (connect B and C, disconnect A and B)
Release button 11: Turn off relay 1 of Receiver 6 (disconnect B and C, connect A and B)
Press and hold button 12: Turn on relay 2 of Receiver 6 (connect B and C, disconnect A and B)
Release button 12: Turn off relay 2 of Receiver 6 (disconnect B and C, connect A and B)
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, another relay Off; Press another button -> Off.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com