- ページ 2

カメラレンズ Canon EF14mm f/2.8L II USMのPDF 使用方法をオンラインで閲覧またはダウンロードできます。Canon EF14mm f/2.8L II USM 2 ページ。 Ef lenses
Canon EF14mm f/2.8L II USM にも：使用方法 (2 ページ), インストラクション (10 ページ), 使用方法 (2 ページ), ユーザーマニュアル (5 ページ)

ページを印刷する

8. Hood

The hood can keep unwanted light out of the lens, and also

protects the lens from rain, snow, and dust. Engage the hood

attachment tabs on the lens with the tabs on the hood and

turn the hood in the direction of the arrow to secure it to the

lens.

[Bayonet type]

EF20mm f/2.8 USM, EF28mm f/1.8 USM and EF50mm

f/1.4 USM (sold separately), and EF24mm f/1.4L USM and

EF35mm f/1.4L USM (supplied with the lens).

To fit the hood on the EF20mm f/2.8 USM, EF24mm f/1.4L

USM, EF28mm f/1.8 USM or EF35mm f/1.4L USM, align

the hood's attachment position mark with the red dot on the

front of the lens, then turn the hood clockwise until the lens's

red dot is aligned with the hood's stop position mark

When attaching or detaching the hood, grasp the base of the

hood to turn it. To prevent deformation, do not grasp the rim

of the hood to turn it.

Though there is no red dot on the hood for the EF50mm f/1.4

USM (ES-71II), the attachment procedure is the same.

• Part of the picture may be blocked if the hood is not

attached properly.

• The hood can be reverse-mounted on the lens for storage.

[Clip-on type]

EF85mm f/1.8 USM, EF100mm f/2 USM (sold separately)

Press the buttons on both sides of the hood to attach as

illustrated

[Cut-in type]

Fixed type EF14mm f/2.8L USM

①

The hood and lens are a single unit.

Pull-out type EF200mm f/2.8L USM

②

Pull the hood out from the front of the lens to use

Specifications

Angle of view

Diagonal

Vertical

EF14mm f/2.8L USM

114°

81°

EF20mm f/2.8 USM

94°

62°

EF24mm f/1.4L USM

84°

53°

EF28mm f/1.8 USM

75°

46°

EF35mm f/1.4L USM

63°

38°

EF50mm f/1.4 USM

46°

27°

EF85mm f/1.8 USM

28°30'

16°

EF100mm f/2 USM

24°

14°

EF200mm f/2.8L USM

12°

7°

*1 Built-in gelatine filter holder

*2 Built-in

CT1-7538-004

The lens length is measured from the mount surface to the

front end of the lens. Add 21.5 mm when including the lens

cap and dust cap.

The size and weight listed are for the lens only, except as

indicated.

Product specifications and appearance are subject to

change without notice.

❾

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be

required to stop operation of the equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled

"Digital Apparatus", ICES-003 of the Industry Canada.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques (de la classe B) prescrites dans le Règlement

sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Lens

Minimum

Max. magnification and field of view

construction

aperture

Horizontal

0.10X/246 × 375 mm (9.7" × 14.8")

104°

10-14

84°

9-11

0.14X/176 × 264 mm (6.9" × 10.4")

0.16X/150 × 227 mm (5.9" × 8.9")

74°

9-11

65°

9-10

0.18X/139 × 212 mm (5.5" × 8.3")

54°

9-11

0.18X/136 × 206 mm (5.4" × 8.1")

40°

6-7

0.15X/164 × 249 mm (6.5" × 9.8")

24°

7-9

0.13X/191 × 287 mm (7.5" × 11.3")

0.14X/175 × 262 mm (6.9" × 10.3")

20°

6-8

10°

7-9

0.16X/152 × 226 mm (6" × 8.9")

❾

●

Min. focusing

Filter diameter

distance

0.25 m/0.82 ft.

*1 <3>

0.25 m/0.82 ft.

72 mm <1>

0.25 m/0.82 ft.

77 mm <1>

0.25 m/0.82 ft.

58 mm <1>

0.3 m/0.98 ft.

72 mm <1>

0.45 m/1.48 ft.

58 mm <2>

0.85 m/2.79 ft.

58 mm <1>

0.9 m/2.95 ft.

58 mm <2>

1.5 m/4.92 ft.

72 mm <2>

●

Hood

Max. diameter and length

77 × 89 mm (3.0" × 3.5")

560 g/19.6 oz.

EW-75II

77.5 × 70.6 mm (3.1" × 2.8")

405 g/14.2 oz.

83.5 × 77.4 mm (3.3" × 3.1")

EW-83DII

550 g/19.4 oz.

EW-63II

73.6 × 55.6 mm (2.9" × 2.2")

310 g/10.9 oz.

EW-78C

79 × 86 mm (3.1" × 3.4")

580 g/20.5 oz.

ES-71II

73.8 × 50.5 mm (2.9" × 2.0")

290 g/10.2 oz.

ET-65III

75 × 71.5 mm (3.0" × 2.8")

425 g/14.9 oz.

75 × 73.5 mm (3.0" × 2.9")

ET-65III

460 g/16.1 oz.

83 × 136.2 mm (3.3" × 5.4")

790 g/27.7 oz.

Weight

Case

LP1016

LP1214

LP814

LP1214

LP1014

LH-D18

2006.9.1