- ページ 33
ソフトウェア Canon EOS DIGITAL REBEL/300D DIGITALのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Canon EOS DIGITAL REBEL/300D DIGITAL 42 ページ。 Canon inc. digital camera utility instruction manual
ページを印刷する
Enables quiet operation when the shutter button is OFF after
P.Fn-21
picture-taking
When single shooting is selected, this function selects quiet camera operation when you
release the shutter button from the fully pressed position to the half way position.
This is useful when the camera operation noise would be disturbing after you take the
picture.
If you select continuous shooting, the camera operates normally.
Setting mirror lockup with C.Fn-12 will further reduce the shooting noise.
Changes the timer's time length
P.Fn-23
After you press and release a button, the respective function remains active for a specific
number of seconds. You can change this number of seconds as necessary.
The function's activation time can be set from 0 to 3600 sec. (1 hour).
If the standard activation time is too short or too long, you can adjust it.
AE lock time after you press the shutter button halfway or the <
6 sec. timer
button.
16 sec. timer
FE lock time after you press the <
Exposure setting retaining time after the picture is taken. Setting
Post-shutter
this to a longer time can make it easier to shoot in the same
release timer
exposure with AE lock.
(2 sec. timer)
LCD panel illumination time after the picture is taken.
Note that if you set a longer activation time, the battery become exhausted more quickly
and the number of possible shots will be reduced.
To turn off the function's activation time midway, press the <
button or <
> button.
Illuminates the LCD panel during bulb exposures
P.Fn-24
After the bulb exposure starts, press the <LCD panel illumination> button to illuminate the
LCD panel until the bulb exposure ends.
Convenient when you want to monitor the elapsed bulb exposure time.
Note that if you take bulb shots for long periods, the battery becomes exhausted more
quickly and the number of possible shots will be reduced.
P.Fn-25
You can use this function to select the default settings when you press the <CLEAR>
button.
Convenient when you want to instantly switch to frequently-used settings.
P.Fn-26
This function is compatible with the EOS-1D Mark II N, EOS-1Ds Mark II and EOS-1D
Mark II.
Normally, the shutter-release time lag is controlled for stability. This Personal Function
eliminates this control. As a result, the shutter-release time lag can be reduced by as much
as about 20 percent when the aperture needs to be stopped down by no more than 3 stops.
This is effective when a shorter shutter-release time lag is more important than a stable
shutter-release time lag.
Since the difference is in 10-millisecond increments, the time lag may not feel any
shorter.
>
P.Fn-27
> button.
The electronic dial's rotational function can be reversed for selecting the AF point and
setting the shutter speed and aperture.
By matching the dial's rotation direction to the particular operation, the operation can feel
more intuitive.
When the Main Dial's rotational function is reversed, the horizontal AF point selection
direction does not change.
P.Fn-28
> button, <
>
The Quick Control Dial cannot be used to set exposure compensation.
This prevents exposure compensation from being set accidentally while the AF point is
being selected.
Sets the default settings when the <CLEAR> button is ON
Shortened release time lag
Enables the electronic dial's function to be used in the reverse
direction
Prevents exposure compensation with the Quick Control Dial
Cover/Table of
Contents
Introduction
1
Downloading Images
from the Camera
2
Setting the Cameras
other than the EOS-1D
Series Cameras
3
Setting the EOS-1D
Series Cameras
4
Remote Shooting
Troubleshooting
Index
3-13