- ページ 2

ドア開閉システム Dorex 1901のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Dorex 1901 2 ページ。

ページを印刷する

REGULAR ARM INSTALLATION

CLOSER MOUNTED ON DOOR ON PULL SIDE

This drawing shown is LEFT HAND DOOR, for RIGHT HAND DOOR install opposite

5-1/2

(140)

Hinges

Centerline

7/8

(22)

9/16

(14)

9/16

(14)

INCH

(mm)

INSTALLATION DIMENSIONS

OPENING

INCHES

101°TO 130°

7-3/32

131°TO 180°

3-15/16

RIGHT

HAND

Hold-Open

Adjusting

Nut

90°

Main

Arm

Forearm

Preload

LEFT

HAND

90°

Preload

Page 2

1-3/4

(44)

1-7/16

(36)

SPRING POWER ADJUSTMENT

11-1/8

(283)

180

100

DOOR CLOSER INSTALLATION

1. Refer to installation instructions supplied with door closer.

2. Adjust spring power to match door size a indicated on chart on page 1.

3. Mount door closer on door using dimensions for the selected door opening

angle, with speed control valves facing the hinges.

4. Disconnect the forearm from the main arm. Place main arm on door closer top

shaft as shown in the illustration and attach with screw.

5. Mount forearm (friction arm) shoe on the door frame using dimensions for the

selected door opening angle. Position hold-open adjusting nut on top for right

hand (RH) door or bottom for left hand (LH) doors.

6. Close door, loosen hold-open adjusting nut (turn clockwise), position forearm

(friction arm) perpendicular to the door surface and adjust its length to connect

to the main arm. Secure friction arm to main arm with screw.

DOOR CLOSER ADJUSTMENTS

1. Refer to adjustment instructions supplied with door closer and pictorials on

page 1.

2. Adjust closing speed and latch speed so that the door closes within 6-7

seconds, evenly divided between sweep speed and latch speed.

3. To adjust the hold-open position, open the door to the desired opening angle

and tighten the adjusting nut (turn counterclockwise) on the friction arm.

Close and open the door and verify that the hold open works.

4. Adjust backcheck if required.

COVER INSTALLATION

1. Place cover over door closer and attach with supplied screws.

2. Place shaft cover on the exposed door closer shaft.

TOP JAMB INSTALLATION

CLOSER MOUNTED TOP JAMB ON PUSH SIDE OF DOOR.

This drawing shown is RIGHT HAND DOOR, for LEFT HAND DOOR install opposite

11-1/8

(283)

SPRING POWER ADJUSTMENT

1-3/4

(44)

Frame Soffit

1-3/4

5-3/8

(44)

(136)

INSTALLATION DIMENSIONS

OPENING

INCHES

101°TO 130°

7-3/32

180

131°TO 180°

3-15/16

100

RIGHT

HAND

Hold-Open

Door opens to

Adjusting Nut

the outside

2 1/2" (63.5 mm)

Reveal

90°

For reveals longer than

Main

2 1/2" (63.5 mm) use

Forearm

Arm

longer forearm rod

(sold separately)

Forearm Rod

Preload

LEFT

HAND

Door opens to

the outside

90°

Preload

9/16

(14)

Hinges

Centerline

9/16

(14)

1/2

(13)

INCH

(mm)

DOOR CLOSER INSTALLATION

1. Refer to installation instructions supplied with door closer.

2. Adjust spring power to match door size as indicated in chart on page 1.

3. Mount door closer on frame top jamb using dimensions for the selected

door opening angle, with speed control valves facing the hinges.

4. Disconnect the forearm from the main arm. Place main arm on door closer

bottom shaft and attach with screw.

5. Mount forearm (friction hold open arm) shoe on door using dimensions for

the selected door opening angle. Position hold-open adjusting nut on

bottom for right hand (RH) door or top for left hand (LH) doors.

6. Close door, loosen hold-open adjusting nut (turn clockwise), position

forearm (friction arm) perpendicular to the door surface and adjust its length

to connect to the main arm. Secure friction arm to main arm with screw.

DOOR CLOSER ADJUSTMENTS

1. Refer to adjustment instructions supplied with door closer and

pictorials on page 1.

2. Adjust closing speed and latch speed so that the door closes within

6-7 seconds, evenly divided between sweep speed and latch speed.

3. To adjust the hold-open position, open the door to the desired

opening angle and tighten the adjusting nut (turn counterclockwise)

on the friction arm. Close and open the door and verify that the hold

open works.

4. Adjust backcheck if required.

COVER INSTALLATION

1. Place cover over door closer and attach with supplied screws.

2. Place shaft cover on the exposed door closer shaft.

Page 3