電源 bolid RIP-24のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。bolid RIP-24 2 ページ。 Battery backed power supply
bolid RIP-24 にも：取扱説明書 (8 ページ)

ページを印刷する

SHUTTING OFF RIP-24

Shut off the mains power supply 220 V.

Detach the batteries.

Remove the fuse F1.

Disconnect the load circuit.

MAINTENANCE

The maintenance of the RIP-24 is to be carried out annually. The maintaining operations include:

1) Visual inspection of the RIP-24 to discover mechanical injures and to clean any dirt or dust if presented.

2) Checking the output voltage value when the load is connected as specified in SPECIFICATION and checking

the output voltage value when the RIP-24 is powered by batteries.

3) Testing LED and sound indication to meet the requirements of Table above.

4) Inspection of proper attaching of the RIP-24, tightening of contacts, and wire integrity.

5) Replacing the batteries when necessary but at least once per 5 years.

MANUFACTURER

ZAO NVP BOLID

#4, Pionerskaya Str., Korolev, Moscow Region, Russia, 141070

Tel./fax +7 495 775-71-55

E-mail: [email protected],

[email protected]

Web-site:

www.bolid.com

BATTERY BACKED POWER SUPPLY

RIP-24 model 01

INSTRUCTION MANUAL

GENERAL

Battery Backed Power Supply RIP-24 model 01 (referred to as RIP-24 below) is designed to provide electric power

to various fire and intrusion detectors as well as control and indicating equipment suited for uninterrupted 24 VDC.

The RIP-24 is round-the-clock operating device with specified output parameters and sealed backup batteries which

are tested and charged automatically. The RIP-24 provides shutting the batteries off from the load circuit to avoid their

unacceptable discharge.

The RIP-24 provides light and audible indication of its current status, i.e. normal or no voltage, battery charge,

output short failure or overload, battery missing or shutting down when discharged.

Being powered by mains power and by backup batteries, the RIP-24 provides its outputs against short circuit

failures with automatic recovering output voltage after repairing the failures.

When operated, the RIP-24 should be protected against atmospheric fallout and mechanical damage. RIP-24 is not

designed to be used in explosion-hazardous premises.

SPECIFICATION

AC Input Voltage Range:

(220+22-33) VAC

Backup Power Supply:

two batteries «Delta» DTM1207 12 V @ 7 Ah or analogous

(with the lifetime of at least 5 years)

No batteries are provided with the power supply

27.0 ± 1.2 VDC at both AC and charged battery powering;

Output Voltage Range:

22.0 ± 1.0 VDC min provided the battery is discharged

Load Current Rating:

3.0 А

Maximum Load Current:

4.0 А for 2 min, once an hour, at both mains and battery power

Input Current Consumption:

0.7 A max at rating load

RIP-24 Consumption From the Battery:

30 mA max

Ripple (mVp-p)×2:

30 mV maximum at rating load current

Battery Low Shutdown:

20.4±1.2 VDC

On Battery Run-Time:

at least 5 hours for 1 A load current at 25°C

(the run-time increases in inverse proportion to the load current)

Pre-Operation Time:

3 seconds max

Operating Temperature Range:

from –10°C to +40°C

Relative Humidity:

up to 90% at +25°C

Overall Dimensions:

340 mm × 270 mm × 100 mm

RIP With Batteries Weight:

12 kg maximum

Typical Lifetime:

10 years, the batteries being to be replaced once every 5 year

The RIP-24 provides outputting a signal to the NPN output in case of switching to powering by the backup batteries

(in state of no mains power) or a short failure in the load circuit. The NPN output is opened when AC line fails and

the RIP-24 is operating in battery mode or in case of a short load circuit failure, and it is closed when the RIP-24 is

100 mA respectively.

The RIP-24 provides connecting two extra 12 V batteries of 17 Ah each placed in a special Box 2x17Ah to increase the

time of operation from the batteries (with total capacity of all RIP-24 batteries being equal to 2×24 Ah).

STANDARD DELIVERY

Battery Backed Power Supply RIP-24 mod.01

Instruction Manual

Fuse 2А

Round Head Wood Screw

Wall Plug

Plastic Bushing

Wire

Lock Key