ページを印刷する
_
4.
Check the wiring and perform a directional test. In
so doing, monitor the signals at the control unit of
the concealed rod multipoint lock.
After a locking signal has been emitted,
locking rod must move down and the bottom limit
switch must be closed.
5.
Set the program sWitch of the ES90/100
unit to "AUTOMATIC".
The concealed
The red fault LED should flash once.
The buzzer should emit a single signal tone.
8.3
Settings
Setting the motor trip current
on the contro! unit of concealed rod multipoint lock.
1.
Turn the potentiometer
to its limit.
2.
Engage and disengage the concealed
multipoint
the green LED.
3.
Gradually turn the potentiometer
the green LEO briefly flashes.
The current
4.
Turn the potentiometer
clockwise
This completes
Check the limit switches and adjust as appropriate.
Check the position of the "locked"
limit switches
and re-adjust
The switches
must be firmly closed in their respective
end positlOns and the rack should not yet have reached
its mechanical
Setting
DIP switch
DIP switch
1 in position
• The LED fault indicator
DIP switch
1 in "OFF" position .
• The LED fault indicator
Setting DIP switch 2 (signal tone).
DIP switch 2 in "ON" position:
• The audible signal emitter
DIP switch 2 in "OFF" position:
• The audible signal emitter
8.4
Functional
Concealed
rod multipoint
A jumper or a switch (m the case of FST doors)
from terminal
standby.
Fault lED (red), selectable
Ix flash means unlocking
3x flashes means lockmg successfully
lights
up when both limit switches are either
open or closed
Continuous
-------------
ES90/100
rod multipoint
lock should unlock.
using the potentiometer
counter-clockwise
rod
lock several times while observing
clockwise
limit has now been reached.
a further small degree
until the LED is extinguished.
the setting operation.
and "Unlocked"
as necessary.
limit.
1 (fault LED).
"ON".
is switched on.
is switched off.
is SWitched on.
is switched off.
tests
lock ON:
12 to 13 places the system on
via DIP switch:
successfully
completed.
completed.
the idle state.
In
Itght signals fault.
Buzzer, selectable
Ix signal means unlocking
completed.
the
3x signals means locking successfully
• Continuous
1 minute.
control
Standby LED (green)
• Ughts up when the motor overcurrent
responds.
A\
The lock may only be operated in the
ill
program switch position.
Unlocking:
• Unlocking
input signal.
locking:
locking
is performed
input signal.
The STOP output disables the door operator
until
during the locking and unlocking
If the locking or unlocking
completed
alarm signal is emitted.
The attempted
twice.
• After a faull, the faulted
second time.
Fixing the limit positions
• Self-locking
the locked and unlocked
NighUbank
With this input signal, It is also possible to
perform an emergency unlocking
opening operation when the program switch is set
to "OFF" or if there is a power failure.
ESU
When the input is open, the anti-tamper
Fault acknowledgement
Once a fault has been rectified,
be cancelled
by briefly switching
switch position
• limit
switch OPEN sets the "Unlocked"
• limit
switch CLOSED sets the "locked"
Manual unlocking
Operation of the manual unlocking
interrupts
limit positions).
locking
and unlocking
manually.
Auxiliary contact for alarm systems
PrOVided on the bottom limit switch of the concealed
rod multipoint
lock is an additional
change-over contact for indicating
This can be connected
via DIP switch
successfully
completed.
signal indicates
fault; shutdown
monitor
"orr"
is performed
on receipt of an
on receipt of an
operation.
operation
is not
within 2 seconds, a short audible
locking operation
is repeated
direction
is tested a
performed
by short-circuited
position.
or an emergency
output
the alarm signal can
"OFP'
to the
(acknowledgement/reset
sequence) .
mechanism
the motor connection
(at pre-adjusted
can be performed
limit switch with a
the locked position.
to an alarm system.
~
DORMA
after
motor in
is set.
program
output.
output.