- ページ 4
バッテリーチャージャー Battery Doctor 20093のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Battery Doctor 20093 4 ページ。 2/10/55 amp battery charger & maintainer instructions for 6 & 12 volt batteries
ページを印刷するBATTERY CHARGING - AC CONNECTIONS
8.
8.1
This battery charger is for use on a nominal 120-volt circuit and has a grounded plug that looks like the plug illustrated. The charger must be
grounded to reduce the risk of electric shock. The plug must be plugged into an outlet that is properly installed and grounded in accordance with
all local codes and ordinances. The plug pins must fi t the receptacle (outlet). Do not use with an ungrounded system.
8.2
Never alter the AC cord or plug provided – if it does not fit the outlet, have a proper grounded outlet installed by a qualified electrician. An
improper connection can result in a risk of electric shock or electrocution.
NOTE: The use of an adapter plug is not recommended.
g
DANGER. Before using adapter as illustrated, be certain that center screw of outlet plate is grounded. The green-colored rigid ear or lug
extending from the adapter must be connected to a properly grounded outlet - make certain it is grounded. If necessary, replace original outlet
cover plate screw with a longer screw that will secure adapter ear or lug to outlet cover plate and make ground connection to grounded outlet.
NOTE: USE OF AN ADAPTER IS NOT ALLOWED IN CANADA. IF A GROUNDING TYPE RECEPTACLE IS NOT AVAILABLE, DO NOT USE THIS APPLIANCE
UNTIL THE PROPER OUTLET IS INSTALLED BY A QUALIFIED ELECTRICIAN.
8.3
Recommended minimum AWG size for extension cord:
AC input rating, amperes*
At least
But less than
0
2
2
3
3
4
4
5
5
6
6
8
8
10
10
12
12
14
14
16
16
18
18
20
*If the input rating of a charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing
the wattage rating by the voltage rating - for example: 1200 watts/120 volts = 10 amperes
Risk of electric shock or fi re.
AWG size of cord
Length of cord feet (m)
25 (7.6)
50 (15.2)
100 (30.5)
18
18
18
18
18
16
18
18
16
18
18
14
18
16
14
18
16
12
18
14
12
16
14
10
16
12
10
16
12
10
14
12
8
14
12
8
1
2
1. Digital LED Display
2. Reverse Polarity Warning LED
3. Charge Complete LED
4. USB Accessory Port
5. Charge/Start Switch
6. Amperage Select Switch
7. Display Volt/Amp Switch
150 (45.6)
8. Alligator Clips
9. USB LED Light
16
14
14
12
12
10
10
8
Before using review all safety and connection directions before using charger. Failure to do so can
8
damage battery and cause serious injury or death.
8
10.1 SELECT SETTING switch use:
55A START — Use this setting for starting a 12V vehicle with a discharged battery.
6
10A–12V — Use this setting for charging large 12 volt batteries. This setting will shut the charger off once the battery is charged.
6
2A–12V
— Use this setting for charging small 12 volt batteries such as lawn mowers, tractors, motorcycles, etc.
(Monitor battery continually, since this rating does not taper or shut off automatically.)
10A–6V — Use this setting for charging 6 volt batteries.
(Monitor battery continually, since this rating does not taper or shut off automatically.)
NOTE: Unless the information is supplied for the particular battery, always charge small 12 Volt batteries at no more than 2 Amps.
10.2 SELECT DISPLAY switch use:
Battery Voltage (Volt) — Use this selection to display the battery's voltage on the LED digital display.
FEATURES
9.
3
4
5
8
10.
OPERATING INSTRUCTIONS
7
6
9