- ページ 9

室内装飾品 Canyon 98-161のPDF 組立説明書をオンラインで閲覧またはダウンロードできます。Canyon 98-161 14 ページ。 Cottage colors collection bunk bed

ページを印刷する

LIST OF CONTENTS

COTTAGE COLORS COLLECTION

BUNK BED END BOX ( 98-706 ) FIG.1

A.- (1) HEADBOARD

BUNK BED TOP END BOX ( 98-705 ) FIG.2

B.- (1) TOP BUNK BED

HARDWARE PACK

C.- (2) METAL DOWEL PINS

6 DRAWER DRESSER BOX ( 98-208 ) FIG.3

D.- (1) 6 DRAWER DRESSER

3 DRAWER COMPUTER DESK BOX ( 98-602 ) FIG.3

E.- (1) 3 DRAWER COMPUTER DESK

6 PCS SIDE RAILS BOX ( 98-730 ) FIG.4

F.- (4) SIDE RAILS

G.-(2) GUARD RAILS

HARDWARE PACK

H.- (24) 80MM FLAT HEAD BOLTS

I.- (24) 5/8" CROSS DOWEL NUTS

J.- (1) 5MM ALLEN WRENCH

4 PCS SLAT PACK BOX ( 98-645,98-646 ) FIG.5

K.- (4) SLATS

HARDWARE PACK

L.- (8) 1 1/4" SCREWS

TWIN/FULL BED BOX ( 98-707,98-709 ) FIG.6

M.- (1) HEADBOARD

N.- (1) FOOTBOARD

LADDER BOX ( 98-720 ) FIG.7

O.- (1) LADDER

HARDWARE PACK

P.- (2) METAL HOOK BRACKETS

Q.- (6) 1" SCREWS

1.- TO ASEMBLE TWIN BUNK BED, USING ONE HEADBOARD (A), ONE TOP BUNK BED (B), TWO SIDE RAILS (F), TWO GUARD RAILS (G), ONE 6 DRAWER DRESSER (D) OR ONE 3 DRAWER COMPUTER DESK (E)

2.- REMOVE FACTORY INSTALLED PLASTIC PLUGS FROM THE TOP OF DRESSER OR THE TOP OF THE DESK , THEN INSERT ONE METAL DOWEL PIN ( C ) IN EACH HOLE OF THE TOP, TAKE THE TOP BUNK BED END (B)

PLACE IT ON TOP OF THE DRESSER OR DESK WITH THE GROVE LINES FACING LIKE FIG.8, ALIGNING THE METAL DOWEL PINS WITH THE BOTTOM HOLES OF TOP BUNK BED END UNTIL ARE ALL THE WAY IN, SEE FIG.8

3.- INSERT TWO CROSS DOWELS (I) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9

4.- ATTACH TWO SIDE RAILS (F),TWO GUARD RAILS (G) TO HEADBOARD (A)&TOP BUNK BED (B),INSERTING TWO 80MM FLAT HEAD BOLTS (H) INTO HEADBOARD&TOP BUNK BED HOLES,USE THE 5MM ALLEN WRENCH

( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),

(j) TO TIGHTEN BOTH FLAT HEAD BOLTS

5.- PLACE 4 SLATS (K) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH HEADBOARD&TOP BUNK BED ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE

FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (L), SEE FIG.11

FIG. 8

REV 01 02/08/16

CANYON FURNITURE COMPANY.

TWIN BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2

(HPK00012)

(HPK00104)

(HPK00016)

(HPK00008)

YES,

HORIZONTAL GROOVE

FIG. 9

FIG. 1

FIG. 2

FIG. 7

REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.10

( USE ONE 4 PCS SLAT PACK (98-645) )

FIG. 10

PAGE 3 OF 5

FIG. 3

FIG. 5

FIG. 6

FIG. 11

FIG. 4

KIS01130