- ページ 2
ドライヤー Double K Industries 850 - 230vのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Double K Industries 850 - 230v 4 ページ。 Animal dryer
ページを印刷するCONGRATULATIONS!
on your purchase of the Double K Challengair 850/850-XL Forced Air
Dryer. The Double K Challengair 850 and 850-XL Dryers produce high-velocity warm air under pressure to
make your grooming tasks easier. Your new dryer is designed to provide long, reliable service.
The 850 and 850-XL are available in both stand and portable models. The stand model is equipped with a
grooming arm for use during table drying. The 850-XL model produces 15% more air than the 850. Both are
available with a variable speed option for greater air ow control.
Please read this manual carefully and completely before beginning operation of your dryer and keep in a
convenient and safe place for future reference. A warranty card is included with your dryer and should be lled
out completely and mailed to Double K Industries within 30 days of the purchase date of your dryer to
validate your warranty. Online registration is available at www.DoubleKIndustries.com.
Your 850/850-XL Challengair Dryer has brush-type motors (Both models have two motors). It is important that
the brushes be changed when they become worn down, to prevent damage to your dryer motors (Brushes are
a maintenance procedure not covered under warranty). We suggest checking the motor brushes after every
600 hours of dryer use. Please see section on "Maintenance -Brushes" p.7, in this manual, for instructions.
IMPORTANT SAFEGUARDS
DO NOT TURN ON DRYER WITHOUT FIRST HOLDING THE DRYER HOSE as the air volume from the dryer can
cause the hose to move and swirl and may cause injury.
1.
Do not leave dryer OR animal unattended while in use.
2.
Unplug unit when not in use.
3.
Do not use extension cords with dryer.
4.
Do not unplug by pulling on cord.
5.
Do not expose dryer to rain or water.
6.
Do not use or store where dryer can fall or be pulled into tub, sink or standing water.
If dryer falls into water...UNPLUG IT...DO NOT REACH INTO THE WATER!
7.
Unplug unit before attempting any service or maintenance.
8.
Do not put any object into dryer openings.
9.
Keep loose clothing, jewelry and hair away from dryer openings.
10.
Do not direct dryer air toward eyes or ears of people or pets.
11.
Never use dryer if it has damaged cord or plug, has been dropped, damaged or exposed to
rain or water. Return to Double K Industries or Authorized Service Center for service.
12.
For use on animals only.
13.
For use by adults only. Use caution when working around children.
14.
Do not use attachments not recommended by Double K Industries.
15.
Operate only with lters in place. Keep lters clean, as dirty lters limit air intake and may
damage the motor or cause overheating.
16.
Plug only into a properly grounded receptacle. Always make sure the amperage of the
electrical outlet is su cient for the amperage of the product. (See front of manual for
amperage rating of this product).
17.
Do not use this product for anything other than its intended use.
18.
Do not attempt to perform any service or maintenance not outlined in this manual.
19.
Do not attempt product modi cations or alterations. Do not use, if any parts or switches are
damaged. Send to an Authorized Service Center or Double K Industries for service.
When servicing, use only Double K Industries parts.
20.
A NOTE ABOUT HEAT: Your Challengair 850/850-XL dryer has no heating element. The Challengair
produces heat by a " ow-thru" motor system, meaning the air is pushed through the motor and is warmed
by the natural heat of the motor that occurs during use. This means greater electrical savings and e ciency
for you. The dryer will reach maximum heat after about 3-5 minutes of use. Obviously, the greater the
ambient temperature, the warmer the air from the dryer.
2
STAND MODEL ASSEMBLY
Your dryer is packaged in two boxes. Your boxes include: Box 1: The dryer body. Box 2: Stand base with casters,
Y-Bar, stand assembly, two 6' twist-on hoses, one arm extension, one air di user, 3 nozzles, 2 hose-to-cage
attachments with tie-wrap fasteners and 2 hose adaptors. To assemble your dryer, rst attach the Y of the
Y-bar between the washers on the knob post. The Y-bar slot has a slight angle to it and should be positioned
pointing toward the front of the dryer. Make sure the electrical cord exits toward the back of the dryer and the
back of the Y-bar. Re-tighten knobs to hold dryer at desired angle. Attach the arm extension to the dryer body
by loosening the nger nuts around the upper air outlet on the dryer body. Align the holes in the arm extension
with the bolts in the dryer face. Tighten nger nuts securely for a snug t.
Assembly of Stand
The stand tube assembly is pre-assembled and wrapped in paper. The stand tube assembly is compressed and
held in position by the center clamp. Loosen the handle on the clamp and allow the spring to extend the tube
assembly. Place the end of the larger outer tube down into the center of the stand base. Twist and push down
rmly. Lift the dryer head assembly, and position over the assembled stand and slide the tube of the Y-bar into
the upper stand tube. With clampling handle still loose, raise or lower dryer to desired height and tighten stand
adjustment handle as explained in the next paragraph.
14
15
13
4
6
16
10
11
9
8
7
12
5
4
2
1
3
Stand Height Adjustment and Dryer Angle Adjustment:
Your dryer has "rachet" type adjustment handles on the stand
and the dryer. To tighten and adjustment handle, turn the
handle clockwise as far as is comfortable. As necessary, for
additional tightening, pull the handle out to disengage the
"rachet" and while keeping the handle pulled out, turn the
handle counter-clockwise to a suitable position for continued
tightening. Release the handle to engage the "rachet" again
and repeat these procedures until the adjustment handle is
tight. Reverse the turning direction of these actions to loosen
the adjustment handle. NOZZLE: The nozzle at the end of the
extension arm may be rotated to change the direction of the
air ow. Simply rotate nozzle to the desired direction.
PORTABLE MODEL
Your portable 850 should include: 2 - 8' twist-on hoses, 1 air
di user, 3 nozzles, 2 hose-to-cage attachments with tie-wrap
fasteners (4 with dual air outlet dryers) and 1 hose adapter
(2 with dual outlet dryers).
PARTS LIST - STAND ASSEMBLY
ITEM
PART
DESCRIPTION
NO.
NUMBER
1
9023
STAND BASE 25" 5-LEG
2
7064
CASTER 3.5" RUBBER WHEEL
3
7063
CASTER LOCKING 3.5" RUBBER WHEEL
4
808
NUT ACORN 5/16-18 UNC ZINC PLATED
5
9020
TUBE 1-5/8 OD X 30" LONG .049 WALL
6
838
TUBE 1-3/8 OD X 241" LONG .049 WALL
7
7019
SCREW #10-32 X 3/4 PHP
8
5531
NUT #10 UNF NYLON INSERT
9
7015
BOLT CARRIAGE 1/4-20 X 1-1/4 LONG
10
7033
HANDLE LEVER ADJUSTABLE 1/4-20 UNC
11
10031
WASHER 1/4 SAE FLAT PLATED
12
830-1
SPRING GAS 36" LIFT-O-MAT
13
887
MOUNTING FORK 850 Y-BAR
14
7048
SPRING COMPRESSION
15
7047
BALL 1/2" CHROMED STEEL
16
7003
CLAMP TUBE STAND ADJUSTMENT SLEEVE
QTY.
1
3
2
2
1
1
1
1
1
1
1
1
1
1
2
1