- ページ 2

産業機器 Dover Triton 9610のPDF 変換マニュアルをオンラインで閲覧またはダウンロードできます。Dover Triton 9610 4 ページ。 Dispensing mechanism
Dover Triton 9610 にも： インストレーション・マニュアル (3 ページ)

ページを印刷する
Dover Triton 9610 変換マニュアル
9600-TO-9610 CONVERSION GUIDE
PURPOSE
The following procedure assumes you are converting a
Model 9600 Cash Dispenser to a Model 9610 Cash
Dispenser, using the 9600-to-9610 Conversion Kit.
PARTS SUPPLIED
P
A
R
T
S
S
1
0
9
0
0
5
0 -
0
1
1
0
D
s i
p
e
n
1
0
3
0
1
1
0 -
0
2
0
7
D
s i
p
e
n
1
0
4
0
0
8
0 -
0
0
1
8
D
a
a t
C
1
0
9
1
2
0
0 -
0
0
3
0
P
o
w
r e
1
2
2
0
0
0
0 -
0
4
0
0
C
r u
e r
n
1
2
2
0
0
0
0 -
0
4
0
1
C
r u
e r
n
1
2
2
0
0
0
0 -
0
4
0
2
C
r u
e r
n
S
c
e r
, w
6
0
2
0
5
4
0 -
0
0
4
9
n i
c
h
9 (
S
c
e r
, w
5
0
2
0
5
4
0 -
0
0
5
0
n i
c
h
9 (
1
0
3
0
7
2
0 -
0
0
0
4
C
a
b
e l
C
S
c
e r
, w
1
0
2
3
0
1
0 -
0
0
0
4
W
a
s
h
r e
1
0
2
0
4
4
0 -
5
1
6
0
A
T
M
C
r e
1
0
7
0
0
0
0 -
0
2
0
0
U
S
C /
a
n
*
C
a
s
s
t e
e t
n i
c
u l
d
e
d
n i
K
t i
w
l l i
U
, S
U
K
r o
C
a
n
a
d
. a
R
E
C
O
M
M
E
N
7
1 /
- 6
n i
c
h
1 (
1
m
m
)
W
e r
n
c
M
e
d
u i
m
P
h
l l i
p i
s
S
c
e r
w
r d
CONVERSION PROCEDURE
1. Open the ATM control panel and turn the power
switch (on the power supply panel) to the OFF (0)
position.
2. Open the vault and disconnect the power and data
cables from the rear of the existing dispenser.
3. Remove the existing dispenser from the slide tray.
TRITON SYSTEMS, INC.
U
P
P
L
E I
D
s
r e
M
e
c
h
a
n
s i
m
s
r e
T
a r
y
a
b
e l
C
a
b
e l
c
y
C
a
s
s
t e
e t
-
U
S
*
c
y
C
a
s
s
t e
e t
-
C
a
n
a
d
a i
* n
c
y
C
a
s
s
t e
e t
-
U
K
*
P
a
n
H
e
a
d
P
h
l l i
p i
, s
#
8
3 -
, 2
/ 3
- 8
m
m
)
P
a
n
H
e
a
d
P
h
l l i
p i
, s
#
8
3 -
, 2
/ 3
- 8
m
m
)
w
E /
t x
T
o
o
h t
W
a
s
h
r e
i l
, p
T
n i
n
r e
m
a
, n
R
u
b
b
r e
C
o
a
e t
d
#
8
3 -
, 2
H
e
x
N
t u
w
E /
t x
T
o
o
h t
f i t
c i
t a
o i
n
L
a
b
e
, l
M
o
d
l e
9
6
1
0
a
d
a i
n
C
r u
e r
n
c
y
L
a
b
l e
d
e
p
e
n
d
u
p
o
n
a t
g r
t e
c
o
u
n
r t
: y
D
E
D
T
O
O
L
S
h
v i
r e
4. Remove the slide tray. Press in on the locking fingers
located on each slide to release the slide members.
Pull the slide tray out and remove it from the cabinet.
5. The slide members attached to the cabinet will be
used for the 9610 slide tray. Remove the six screws
that hold the tray slide members to the old tray and
attach those slide members to the 9610 slide tray,
using six (6) included 3/8-inch (9 mm) Pan Head
Phillips Screws. Place the 9610 slide tray back
onto the cabinet slide members.
Remove slide member from the tray.
Front of Tray.
Attach slides to tray using first set of holes
(three screws per slide).
6. Unlock and open the ATM control panel. Open the
power supply panel (on the right side of the card
cage) and disconnect the existing mech DC power
cable from the backplane connector.
Install the 9610 DC power cable into the backplane
connector, as shown. Route the other end of the
cable down through the oval cutout in the bottom of
the card cage and into the cabinet below.
Route the end of the DC Power Cable down through
the cutout in the rear of the right rail bracket and let
it hang beneath the bracket.
2