- ページ 3

ペイントスプレー Dow ENERFOAMのPDF インストールに関する推奨事項をオンラインで閲覧またはダウンロードできます。Dow ENERFOAM 4 ページ。 Professional foam sealant

ページを印刷する

installation information . commercial/residential

4. If the gap is overfilled, stuff

excess cured foam into the gap

with a blunt tool or trim away

with a sharp knife. Foam will be

tack-free in less than 20 minutes

and can be trimmed in 1/2 hour.

It is fully cured 1 hour after

application.**

5. Clean foam dispensing gun

periodically by rubbing the end

on soft wood to free it from

foam. Do not use a sharp object

to clean foam dispensing gun.

Use a solvent cleaner such as

gun cleaner, acetone or other

adhesive remover between

extended periods of non-use.

6. To store partially used can,

tighten flow control screw

closed and store can upright

with gun attached. Use can

within 30 days of initial use.

7. To reuse, shake can vigorously

for 1 minute before dispensing

and follow dispensing

instructions stated above.

Tip: always close the flow

control knob when the gun is

not in use.

Tip: Treat your gun like a tool.

The better you take care of it,

the longer it will last.

STraw-applied verSion:

1. Attach the nozzle by twisting it

clockwise into the valve. Press

the button until the appropriate

size of foam bead is achieved.

Fill gap less than 1/3 full to

allow for proper expansion.

2. If the gap is overfilled, stuff

excess cured foam into the gap

with a blunt tool or trim away

with a sharp knife. Foam will be

tack-free in less than 20 minutes

and can be trimmed in 1/2 hour.

It is fully cured 1 hour after

application.**

3. Clean straw periodically by

rubbing the end on soft wood to

free it from foam.

4. When finished, bend the straw

back onto the plug on top of

the trigger assembly. The plug

prevents moisture from entering

and curing inside the straw or

valve.

5. To use after storage, gently

rotate or twist the straw to break

the adhesive bond of the foam.

Pull the straw off of the plug and

dispense.

®™Trademark of The Dow Chemical Company ("Dow") or an affiliated company of Dow

**Dependent upon temperature, relative humidity and size of foam bead

c l e a n u P

• On solid surfaces, uncured

foam can be dissolved with

gun cleaner, acetone or other

adhesive remover. Cured foam

must be mechanically removed

or allowed to wear off in time.

• To clean foam dispensing gun,

install a can of gun cleaner,

acetone or other adhesive

remover to the foam dispensing

gun and spray until all foam

is blown out of the foam

dispensing gun and only cleaner

is visible (approximately half

the can of cleaner will be used).

Allow the gun to sit for several

minutes and repeat with a

second flush.

• Do not leave a can of cleaner

mounted on the foam

dispensing gun. This will

dissolve the lip seals inside

the gun and render it useless.

Foam escaping at the handle or

trigger indicates a faulty seal. If

this happens, the gun should be

replaced. If the foam dispensing

gun has not been cleaned, add

a new can of ENERFOAM™

Professional Foam Sealant

immediately. If left without a can

attached, exposure to air and

moisture will cause the foam in

the gun to cure.

d i S P o S a l

• Disposal of full or partially

used aerosol cans must be in

compliance with all federal,

state/provincial and local laws

and regulations. Regulations

vary in different locations.

Empty cans are not considered

hazardous waste and may be

disposed of an nonhazardous

household waste.

S a F e t Y a n d

c o n d i t i o n S o F u S e

• Read the label and Material

Safety Data Sheet carefully

before use.

• ENERFOAM™ Professional

Foam Sealant contains

isocyanate and a flammable

blowing agent. vapor may

travel to other rooms. Ensure

adequate ventilation. Shut off

all pilot lights and extinguish

open flames; eliminate all

sources of ignition before use.

Do not smoke or use lighters or

matches while dispensing foam.

• Do not breathe vapor or mist.

Use in well-ventilated areas

or wear proper respiratory

protection. Isocyanate is

irritating to the eyes, skin and

respiratory system, and may

cause sensitization by inhalation

or skin contact.

• ENERFOAM™ Professional

Foam Sealant is very sticky and

will adhere to most surfaces

and skin. Do not get foam

on skin. Wear long sleeves,

gloves, and goggles or safety

glasses. Cured foam must

be mechanically removed or

allowed to wear off in time.

• The contents are under

pressure. The can may burst if

left in areas susceptible to high

temperatures, such as motor

vehicles, or near radiators,

stoves or other sources of heat.

Do not place can in hot water.

Do not puncture, incinerate or

store at temperatures above

120°F (49°C).

• ENERFOAM™ Professional

Foam Sealant may be used

on vinyl, wood, composite

and metal (aluminum or steel)

substrates. The product adheres

best when surfaces are clean

and free of oil or chemicals.

• Extremely cold temperatures

can affect dispensing perfor-

mance.

• Skin of cured foam can

discolor if exposed to direct

or continuous sunlight for 24

hours or more. Foam should be

painted or coated if prolonged

exposure to sunlight is

expected.

• Using foam dispensing guns

(shown in Figure 1) simplifies

the application of ENERFOAM™

Professional Foam Sealant. In

addition to enabling pinpoint

application control, an airtight

and moisture-tight seal between

the gun and the can prevents

the foam from curing and

blocking the dispensing valve.