リモコン Comcast XR2のPDF スタートをオンラインで閲覧またはダウンロードできます。Comcast XR2 2 ページ。
Comcast XR2 にも：ユーザーマニュアル (2 ページ)

ページを印刷する

Meet Your Remote

XR2

Xfinity Remote

All Power

TV Power

TV Input

Changes to the next

available input on your TV

(if programmed in Step 4)

Discover content by

channel, program or

key words.

XFINITY / Menu

Start

Access Guide, Saved,

XFINITY On Demand, Apps,

Search and Settings.

Number Keys

Setup

Swap

Program remote for Aim

Switches between two DVR

Anywhere or to control your

tuners so you can control

TV or audio device.

playback of two channels.

Turn On Your Remote

Program Your Remote To Control Your

Set-Top Box

Install batteries in the remote and turn on your devices.

Your remote is preprogrammed to operate XFINITY cable boxes. If you are

using the remote for control of a non-XFINITY cable box, you may need to

program the remote for the Motorola or Cisco mode. Follow the steps below to

program your remote.

To set up your remote, first install AA batteries

(sold separately). The All Power key will blink

green four times as the remote powers up

(about 5 seconds).

Back

Turn on your TV.

Turn on your cable box.

Pair Remote for "Aim Anywhere" Control

Control your cable box without having to point at it, even when it is inside a

cabinet or entertainment center.

Aim Anywhere is only supported on certain XFINITY cable boxes. To see if your

cable box supports Aim Anywhere control visit xfinity.com/remotes

Press the Setup button until the All Power key

on the remote changes from red to green.

Press B for control of a Motorola brand

Press the XFINITY button.

cable box; press C for control of a Cisco

or Scientific-Atlanta brand cable box.

Note: If you need to re-program the remote

for control of an XFINITY cable box, repeat

the steps above and press A in step 2.

Press the XFINITY key to check that your

Follow the on-screen instruction to enter the

remote controls your set-top box. If it does,

3-digit code that appears.

you're all set. If not, repeat these steps but

press C for Cisco mode or A for XFINITY

Once the code is correctly entered, your

mode in step B.

XFINITY Remote is paired with the device.

Once the code is correctly entered, your

XFINITY Remote is paired with the device.

Not working? Make sure to install batteries in the

remote, check that your TV is on and that you are

entering the correct 3-digit code on your TV screen.

Need to remove Aim Anywhere control? Press

and hold the Setup button on the remote until the

status LED changes from red to green. Press A on

the remote. If the status LED blinks green twice,

you have successfully removed Aim Anywhere.

Control Your TV's Power and Volume

Popular TV Manufacturer Codes

Emerson

11864, 10171

Using the list on the right, find the first

Insignia

12049, 11641

5-digit code for your TV manufacturer.

JVC

11774, 12321

Press and hold the Setup button (about 3

12731, 10178

seconds) until the Status LED changes from

red to green.

Magnavox

10054, 12597

Panasonic

11480, 10051

Philips

11867, 12597

RCA

10047, 11447

Samsung

12051, 10702

Enter in the first 5-digit code for you TV

Sanyo

10154, 11142

manufacturer. The Status LED should blink

Sharp

10093, 12360

green twice.

Sony

10810, 11685

Toshiba

10156, 11524

VIZIO

11758, 12707

Westinghouse

11712, 13579

If your code isn't listed or you would

like to control an audio device, visit

Verify that the code was accepted by using

your remote to adjust volume and turn the

xfinity.com/remotes

TV on and off.

Not working? Try the second code listed. Still

not working? Visit xfinity.com/remotes for a

complete list of codes or use the My Account

app for mobile (iOS/Android) or X1.

FCC Compliance Statement

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not used in accordance with

the instructions, may cause harmful interference to

radio communications.

There is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, the user is encouraged to try to correct

the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

Increase or decrease the separation between

•

the equipment and receiver.

•

Connect the equipment into an outlet on a

circuit different from that which the receiver is

connected.

•

Consult the dealer or an experienced remote

control/ TV technician for help.

•

It is strongly recommended that the TV be

plugged into a separate wall outlet.

The user is cautioned that changes and modifications

made to this equipment without the approval of

the manufacturer could void the user's authority to

operate this equipment. This device complies with

part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This device may

not cause harmful interference, and (2) this device

must accept any interference received, including

interference that may cause undesired operation.