- ページ 5

キャッシュカウンター Amseco VDP-100のPDF 取扱説明書およびユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Amseco VDP-100 7 ページ。 Video-eye people counter

ページを印刷する

Installation Procedures / Front Panel Controls and Names

5) Wiring Diagrams

Refer to the following wiring diagram and make sure your connections are correct before turning on the

system.

VIDEO SENSOR UNIT

REAL PANEL

MONITOR (Optional)

Video Sensor Unit

Cn1: Connector to CMOS Camera

Cn3: Chime Speaker Connector

Video Signal Input

(-):

Ground

+5V:

DC 5V Power Output

AGC1: Automatic Gain Control 1

AGC2: Automatic Gain Control 2

Cn2: Connector to Counter Display

Cn4: Connector to Monitor

(-):

* U RXQ G

V: Video Signal Output

+12V:

12V DC Input

(-): Ground

EXIT:

(-) Exit

ENTRY: (-) Entry Signal output

6. Front Panel Controls and Names

Counter Display

1) Digital Counter LED Display : displays the accumulated number of entry / exit

events depending on the status of Entry / Exit indication switch.

2) Entry / Exit indication switch:

At ENTRY position - the LED display indicates the number of entry events.

At EXIT position -

the LED display indicates the number of exit events.

3) Counter Display Status Indicator:

Indicate whether the counter is displaying ENTRY counts or EXIT counts.

1 1

ENTRY or EXIT LED blinks for 5 seconds when entry or exit events occur.

2 2

CM-4

Electronic Chime

COUNTER DISPLAY

(Optional)

JP2

(-)

+12V

EXIT

ENT.

CHIME SEL.

JP1

SW4

TRIP LEVELS

ON:HIGH

ENTRY EXIT

Red

+12V

Black

(-)

Orange

EXIT

Brown

ENTRY

White

To AC Outlet

Counter Display

+12V:

12V DC Output

(-):

Ground for DC Output

EXIT:

(-) Signal Input for Exit Events

ENTRY: (-) 6 L JQ DO ,Q SXW IRU ( ntry ( YHQ W V

AC:

12V AC Input

AC:

12V AC Input

BZ1:

Unused

(Reserved for future use)

3 3

ENTRY

EXIT

1 1

2 2

Installation Procedures

5. Installation Procedures

1) Plan the Installation: Decide the Position of Camera / Controller Unit First

VDP-100 senses the people's movement in a certain Detection Area and analyzes the traffic in the Area using

motion tracking technology. It is important to locate the Video Sensor Unit 1) to fully utilize the Detection Area of

VDP-100, and 2) to clear the area from any movements confusing the counter.

Detection Area of the VDP-100 is different depending on the installation heights from the floor, and therefore we

recommend you determine the detection area of the VDP-100 at your intended installation height, and

find the best location of your VDP-100 before starting any other installation procedure.

Please decide the best position of VDP-100 in the following steps before starting any installation :

Step 1) Refer to Fig.1 and find the dimensions of detection area at your intended installation height

Step 2) Stand facing the center of the door, and assume a square of detection area on the floor.

SW2

RESET

Step 3) Make sure people will cross at least 2/3 of the detection area when they enter.

Step 4) Make sure that the detection area is not crossing the door or the wall. Move the VDP-100 if

necessary.

Step 5) Make sure the area is clear from any unnecessary movement.

Step 6) The ceiling right above the center of the detection area is where you install your VDP-100 Video

Sensor Unit.

At 14ft Insttallation Height

At 12ft Insttallation Height

At 10ft Insttallation Height

At 8ft Insttallation Height

6ft

9ft

11ft 13ft

10ft

12ft

14ft

17ft

Fig. 1 Installation Heights and Detection Area