- ページ 15

冷蔵庫 Electrolux #のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Electrolux # 20 ページ。 Over the range microwave oven
Electrolux # にも：取付説明書 (8 ページ), 取扱説明書 (20 ページ), 取扱説明書 (36 ページ), 取扱説明書 (24 ページ), 取扱説明書 (38 ページ), レシピブック (17 ページ), 取扱説明書 (12 ページ), 取扱説明書 (16 ページ), 取扱説明書 (12 ページ), 吸引マニュアル (16 ページ), ユーザーマニュアル (11 ページ), 取扱説明書 (26 ページ), 取扱説明書 (38 ページ), オーナーズマニュアル (9 ページ), 取扱説明書 (16 ページ), 取扱説明書 (16 ページ), 取付説明書 (21 ページ), オーナーズマニュアル (16 ページ), 取扱説明書 (16 ページ), サービスマニュアル (49 ページ)

ページを印刷する

General Care & Cleaning

CLEANING THE BURNER GRATES, BURNER CAPS AND

BURNER HEADS

The Grates, Burner Caps and the Large 18k Burner Head should

be routinely cleaned. Keeping the burner ports clean will prevent

improper ignition and an uneven ﬂame. If needed, the ﬁxed burners

should be cleaned in place with an humid cloth (do not spray water

on them).

Refer to the following instructions:

To Remove and Replace the Surface Burner Grate, Surface

Burner Cap and Surface Burner Head- Remove in the following

order; (1st) Surface Burner Grate, (2nd) Surface Burner Cap, (3rd)

Surface Burner Head (See Figure 1).

Reverse the procedure above to replace the Surface Burner Cap,

Surface Burner Head and Surface Burner Grate. Do not remove

any burner parts from the cooktop until the burner parts have

completely cooled and are safe to handle. Do not operate the

surface burners without the Surface Burner Heads, Surface

Burner Caps and Surface Burner Grates properly in place.

To Clean the Burner Caps, Burner Heads and Burner Grates -

Use a soap-ﬁlled scouring pad or a mild abrasive cleaner to clean

the surface burner caps and surface burner heads. The Grates are

designed to be Dishwasher safe for cleaning. The ports (or slots)

around the burner heads must be routinely cleaned. If residue still

remains in these ports, use a small-gauge wire or needle to clean the slots or holes being

careful not to damage the electrode. For proper ﬂow of gas and ignition of the burner—DO

NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER

THE GAS ORIFICE HOLDER OPENING. ALWAYS make sure that the surface burner cap,

the surface burner head and the surface burner grate are properly in place whenever a surface

burner is in use.

Surface Burner

Grate

THE COOKTOP IS NOT REMOVABLE. Do not attempt to remove or lift the cooktop.

CAUTION

- Use caution when replacing the burner head so the electrode is not damaged. A damaged electrode

may cause a delayed ignition or prevent the burner from igniting

- Any additions, changes or conversions required in order for this appliance to perform satisfactorily

must be made by a qualiﬁed service technician.

Surface Burner

Caps

Surface Burner Grate

1st

2nd

3rd

Electrode

Oriﬁce

Surface Burner

Head

Surface

Burner

Cap

Surface

Burner

Head

Figure 1