- ページ 9

食器洗い機 Bosch 800 SeriesのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Bosch 800 Series 28 ページ。 Built-in wall ovens
Bosch 800 Series にも： 取付説明書 (24 ページ), インストレーション・マニュアル (40 ページ), 取扱説明書 (12 ページ), インストレーション・マニュアル (23 ページ), インストレーション・マニュアル (28 ページ), インストレーション・マニュアル (32 ページ), 取扱説明書 (32 ページ), インストレーション・マニュアル (32 ページ), クイック・スタートと安全マニュアル (7 ページ), 取扱説明書 (40 ページ), インストレーション・マニュアル (40 ページ), インストレーション・マニュアル (32 ページ), 取付説明書 (40 ページ), インストレーション・マニュアル (48 ページ), 取扱説明書 (33 ページ), 取扱説明書 (49 ページ), クイック・スタート・マニュアル (7 ページ), クイック・スタートと安全マニュアル (13 ページ), インストレーション・マニュアル (32 ページ), サービスマニュアル (36 ページ), 取付説明書 (29 ページ), 取扱説明書 (24 ページ), 取扱説明書 (40 ページ)

ページを印刷する
Bosch 800 Series 取付説明書
Method
B
-
To
household or field wiring
1. Remove the dishwasher electrical supply junction
box (Part L) cover and connect to the power
supply cord from the house installation. See
Figure 6.
2. Remove 2" to 3" (51 – 76 mm) of the outer
casing of the household or field supply wiring as
shown in Figure 7. Remove 3/8" to 1/2" (10 – 13
mm) of the insulation from each wire as shown in
Figure 7.
3. Insert the bare copper or green wire(ground) to
the "G"
ground connection of the terminal
block and securely tighten the terminal block
screw (see Figure 6).
4. Insert the white (neutral) wire to the "N"
connection of the terminal block and securely
tighten the terminal block screw.
5. Insert the black (hot) wire to the "L" connection of
the terminal block and securely tighten the
terminal block screw.
6. Check all electrical connections to make sure
they are secure and then attach the junction box
cover with the 4 screws.
WARNING
Avoid Electrical Shock Hazard!
To avoid possible injury or property damage, care should
be exercised when the dishwasher is installed or removed
to reduce the likelihood of damage to the power cord
permanently
connect
Figure 6
Figure 7
to
Inlet Water Connections
Hot Water Supply
The hot water heater should be set to deliver
approximately 120° F (49° C) water to the
dishwasher. Water that is too hot can cause some
detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water
supply pressure must be between 15 - 145 psi (1 -
10 bar).
IMPORTANT NOTES:
If using a solder joint instead of a compression
fitting, be sure to make all solder connections
before connecting the water supply line to the
dishwasher.
Make sure there are no sharp bends or kinks in
the water line that might restrict water flow.
Always use the appropriate seal when making
plumbing connections.
Before connecting the water supply line to the
dishwasher, flush the incoming water line for
approximately 5 minutes to clear any foreign
material.
Turn on the water supply and check for leaks
after connections are made.
Do not perform any work on a charged hot water line.
Serious injury could result. Only qualified plumbers should
perform plumbing work. Do not attempt any work on the
dishwasher hot water supply plumbing until you are certain
the hot water supply is shut off.
Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Water Supply Shut Off Valve
Install an easily accessible shut-off valve (not
supplied) in the hot water supply line, as shown in
Figure 8. All solder connections must be made before
the water line is connected to the dishwasher.
Connecting the Hot Water Supply
There are two plastic corrugated hoses that exit the
back of the dishwasher. The larger hose, with the
brass fitting on the end, is the water supply hose to
the dishwasher (the other hose is the dishwasher
drain hose). You will need a 3 x 13/4 (76 x 45 mm)
opening through the cabinet to pass the dish-washer
.
water supply line through toward the shut off valve.
WARNING
Avoid Scald Hazard!
CAUTION
7