- ページ 21

食器洗い機 Bosch DISHWASHERのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch DISHWASHER 38 ページ。 Dishwasher bosch
Bosch DISHWASHER にも： 取扱説明書 (30 ページ), 取付説明書 (34 ページ), 取扱説明書 (30 ページ), 取扱説明書 (28 ページ), 取扱説明書 (30 ページ), 取扱説明書 (42 ページ), 取扱説明書 (32 ページ), 取扱説明書 (36 ページ), 取扱説明書 (30 ページ), 取扱説明書 (24 ページ), 取扱説明書 (26 ページ), 取扱説明書 (40 ページ), 取扱説明書 (28 ページ), 取扱説明書 (29 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取付説明書 (50 ページ), 取付説明書 (20 ページ), 操作方法 (24 ページ), 操作説明 (36 ページ), 取扱説明書 (25 ページ), 取扱説明書 (46 ページ), 取扱説明書 (31 ページ)

ページを印刷する
Bosch DISHWASHER 取扱説明書
5. Press START button @, timer
programming is activated.
6. To delete the preselected starting
time, press the button P until
indicated on the digital display.
You can change your programme
selection at any time until the
programme starts.

End of programme

The programme has ended when the
value :
is indicated on the numerical
display H.
Switching off automatically
after the end of
the programme *
* depending on model
To save energy, the dishwasher is
switched off 1 minute after the
programme ends (factory setting).
Automatic disconnection
can be adjusted from
:
Appliance does not switch off
automatically
:
Off after 1 min
:
Off after 120 min
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press and hold down the START
button @.
4. Rotate programme selector 8
until : ... s indicated on the digital
display H.
5. Release button.
The factory set value
the digital display H.
is
Sw i t c h i n g o f f a u t o m a t i c a l l y af t e r t h e e n d of t h e pr o g r a m m e
:
to :
.
:
is lit on
Operating the appliance
To change the setting:
1. Rotate programme selector 8 until
the required value is indicated on the
digital display H.
2. Press START button @.
The set value is saved.

Switching off the appliance

Short time after the end of the
programme:
1. Switch off ON/OFF switch (.
2. Turn off the tap (not applicable if
Aqua-Stop fitted).
3. Remove the utensils when they have
cooled down.
Note
When the programme ends, leave
the appliance to cool down a while
before opening it. This will prevent
steam from escaping and causing long-
term damage to your built-in furniture.

Interrupting the programme

1. Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave
the door ajar for several minutes and
then close. Otherwise, expansion
(pressure) may cause the appliance
door to spring open or water to run
out of the appliance.
2. To continue the programme, switch
on the ON/OFF switch ( again.
en
21