- ページ 2

スイッチ Advanced Control HomePro ZDW100のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Advanced Control HomePro ZDW100 3 ページ。 Radio frequency controlled, 300w, 120 vac, wall mounted dimmer switch

ページを印刷する

Wire this Wall Mounted Dimmer in place of a current wall switch according to the diagram. Refer to the Wireless

Controller operating instructions to add this module under the command of the Wireless Controller.

Wall Mounted Dimmer Configuration

The Wall Mounted Dimmer switch locally controls the load ON and OFF. Adjust its dimming level by pressing and

holding the top of the switch for Brighten, press and hold the bottom of the switch for Dim. Push on the top or the

bottom of the switch to configure the module to operate from the wireless controller. With the Wireless Controller,

the Wall Mounted Dimmer can be switched ON and OFF remotely, dimmed remotely and can be included in groups

of lights that operate at the same time (a group can also be a single module), and in scenes that set a lighting mood.

Switch power ON and OFF locally

When the switch is pressed on the top the power will turn ON if off. Press the bottom of the switch and the power

will turn OFF if it was on.

Dimming

If the bottom of the switch is pressed and held the light will dim. When the top is pressed and held, the light will

brighten.

Child Protection

The Wall Mounted Dimmer can be set in a child protect mode by the Wireless Controller. When this mode is active,

a user will have to press the Wall Mounted Dimmer 3 times rapidly to activate the attached load. The module

operates normally when controlled by the Wireless Controller..

Other functions

The switch on the Wall Mounted Dimmer also plays a role as a reset in addition to adding module to groups and

scenes. This is described in more detail in the Wireless Controller instructions.

Air Gap Switch

The ZDW100 has an air gap switch on the face (lower left), that when pulled out, completely removes the power

available to the load (more so than simply turning the dimmer off). This enables the lamps that are controlled by

the device to be changed with minimal danger of electrical shock. The air gap switch must be pushed all the way

back in for the dimmer to operate the lamps again.

Software fuse

This Wall Mounted Dimmer is designed to protect itself against loads that exceed it's maximum power rating. The

application of a load that exceeds that rating is quickly sensed by the dimmer and it responds by immediately

shutting off all power to that load.

If the dimmer doesn't seem to work, or only works momentarily, check to see that the total lamp wattage doesn't

exceed the 300W rating of the dimmer. If a properly sized load is restored to the dimmer, it can be operated

normally once again.

Over-current protection

The Wall Mounted Dimmer hardware also has an over current detection circuit as final protection against overload.

If the software fuse should fail to shut down the dimmer when overloaded, backup protection is provided by an

internal fuse. This internal fuse is not user serviceable. Check your home circuit breakers before concluding that

the product must be returned to manufacturer for repair at a nominal charge.

Operation Note

When a light bulb reaches the end of it's life and burns out, it sometimes creates a momentary short circuit. The

high current that results may cause the dimmer to properly respond by turning off. Should this happen, replace

the bulb with a new one. The dimmer can then be operated to restore power to the light.

WARRANTY

Advanced Control Technologies, Inc. gives this expressed warranty (along with extended warranty endorsements, where applicable) in lieu of

all other warranties, express or implied, including (without limitation), warranties of merchantability and fitness for a particular purpose. This

constitutes Advanced Control Technologies, Inc.'s sole warranty and obligation with regard to our products as well as the Customer's sole

remedy.

Advanced Control Technologies, Inc. expressly disclaims all liability and responsibility for any special, indirect or consequential damages or any

further loss of any kind whatsoever resulting from the use of our product. The Customer's sole and exclusive remedy and the limit of Advanced

Control Technologies, Inc.'s liability for any loss whatsoever, shall not exceed the purchase price paid by the Customer for the product to which

a claim is made.

ZDW100 Instructions

P/D 082703

0618-01

HomePro

by ADVANCED CONTROL TECHNOLOGIES, INC.