- ページ 32

食器洗い機 Bosch DISHWASHERのPDF 操作説明をオンラインで閲覧またはダウンロードできます。Bosch DISHWASHER 36 ページ。 Dishwasher bosch
Bosch DISHWASHER にも： 取扱説明書 (30 ページ), 取付説明書 (34 ページ), 取扱説明書 (30 ページ), 取扱説明書 (28 ページ), 取扱説明書 (30 ページ), 取扱説明書 (38 ページ), 取扱説明書 (42 ページ), 取扱説明書 (32 ページ), 取扱説明書 (36 ページ), 取扱説明書 (30 ページ), 取扱説明書 (24 ページ), 取扱説明書 (26 ページ), 取扱説明書 (40 ページ), 取扱説明書 (28 ページ), 取扱説明書 (29 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ), 取付説明書 (50 ページ), 取付説明書 (20 ページ), 操作方法 (24 ページ), 取扱説明書 (25 ページ), 取扱説明書 (46 ページ), 取扱説明書 (31 ページ)

ページを印刷する
Bosch DISHWASHER 操作説明
aus
Installation and connection
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing
valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
for cold water connection only.

Electrical connection

Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 9*.
The socket must be near
the appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side
to satisfy the relevant safety
instructions.
The connection may be modified by
technicians only.
A power cord extension may be
purchased from customer service
only.
Use only a residual current operated
circuit-breaker which features
the symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply
is connected.
32

Removing the appliance

Also observe
the sequence of worksteps here.
1. Disconnect the appliance from
the power supply.
2. Turn off the water supply.
3. Disconnect the waste water
and fresh water connections.
4. Loosen fastening screws for the
furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully
pulling the hose behind.

Transportation

Empty the dishwasher and secure loose
parts.
Drain the appliance according to the
following steps:
1. Turn on the tap.
2. Close the door.
3. Switch on ON/OFF switch (.
4. Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display
h.
5. Press START button P.
Programme sequence starts.
6. After approx. 4 minutes press the
START button P until :
indicated on the digital display.
After approx. 1 min :
on the digital display .
7. Switch off ON/OFF switch (.
8. Turn off the tap, disconnect supply
hose and drain water.
Transport appliance upright only.
(This prevents residual water from
running into the machine control and
damaging the programme sequence.)
is
is indicated