- ページ 37

食器洗い機 Bosch SB SeriesのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch SB Series 40 ページ。 Dishwasher bosch
Bosch SB Series にも： 取扱説明書 (38 ページ), 取扱説明書 (38 ページ), 取扱説明書 (42 ページ), 操作説明 (36 ページ), 取扱説明書 (38 ページ), 取扱説明書 (48 ページ), 取扱説明書 (40 ページ), 取扱説明書 (44 ページ), 取扱説明書 (50 ページ), 取扱説明書 (44 ページ), 取扱説明書 (40 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (44 ページ), 取扱説明書 (40 ページ), 取扱説明書 (46 ページ), 取扱説明書 (40 ページ), 取扱説明書 (46 ページ), 取扱説明書 (50 ページ), 取扱説明書 (50 ページ), 取扱説明書 (48 ページ), 取扱説明書 (42 ページ), 取扱説明書 (40 ページ), 取扱説明書 (44 ページ), 取扱説明書 (42 ページ), 取扱説明書 (40 ページ), 取扱説明書 (40 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (44 ページ), 取扱説明書 (44 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (50 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (48 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (50 ページ), 取扱説明書 (40 ページ), 取扱説明書 (42 ページ), 取扱説明書 (42 ページ), 取扱説明書 (48 ページ), 取扱説明書 (42 ページ), 取扱説明書 (40 ページ)

ページを印刷する
Bosch SB Series 取扱説明書

Drinking water connection

1. Fasten the drinking water connection
to the tap according
to the installation instructions using
the enclosed parts.
Ensure that the drinking water
connection is not kinked, crushed
or twisted.
2. When replacing the appliance,
always use a new water supply hose.
Water pressure:
At least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing
valve ahead.
Inlet rate:
Minimum 10 litres/minute
Water temperature:
Cold water; hot water max. temperature
60 °C.

Warm water connection *

* depending on model
The dishwasher can be connected
to cold or hot water up to max. 60 °C.
Connection to hot water
is recommended if the hot water can be
supplied by energetically favourable
means and from a suitable installation,
e.g. solar heating system with circulation
line.
This will save energy and time.
The hot water setting :
to adjust your appliance optimally
to operation with hot water.
It is recommended to have a water
temperature (temperature of the
incoming water) of at least 40 °C
and no more than 60 °C.
It is not recommended to connect
the appliance to hot water if the water
is supplied from an electric boiler.
W a r m w a t e r c o n n e c t i o n
allows you
Installation and connection
Setting hot water:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Hold down programme button #
and press START button )"
until : ... is indicated on the digital
display.
4. Release both buttons.
The LED for button # flashes and
the digital display 8 displays the
factory setting :
5. Press programme button # until
the factory set value :
is indicated on the digital
display 8.
To change the setting:
1. By pressing the 3 button, you can
switch the hot water setting off :
or on :
.
2. Press START button )".
The set value is saved.
3. Close the door.

Electrical connection

Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 92.
The socket must be near
the appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side
to satisfy the relevant safety
instructions.
The connection may be modified by
technicians only.
A power cord extension may be
purchased from customer service
only.
en
.
37