- ページ 10

エアコン AirStage AGYE012GCAHのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。AirStage AGYE012GCAH 15 ページ。 Indoor unit (floor type)
AirStage AGYE012GCAH にも：取扱説明書 (8 ページ)

ページを印刷する

6. FINISHING

After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform

this section.

Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do

so may cause water leaks.

6.1. Connection pipe, cable and drain hose

(1) Insulate between pipes.

• Overlap the connection pipe heat insulation and indoor unit pipe heat insulation.

• Wrapping the connection pipe with cloth tape over the range within which they fit into the

rear piping housing section.

• Fasten the pipe bracket with the screw.

(2) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain

water and wind cannot blow in.

(3) Fasten the drain hose to the outside wall, etc.

Cloth

Insulation of indoor

tape

unit pipes

There

are no

gaps

Pipe

bracket

Overlap

Insulation of

refrigerant pipes

Screw

Left piping

Cable

Pipe

Drain hose

Fill the gap between the

knockout hole of the indoor

unit and the pipe or cable

with putty.

Check the following:

GOOD

Stopping

downward

End of drain hose

is immersed in

water.

Drainage

channel

7. FIELD SETTING

There are 3 methods for address setting by FIELD SETTING as follows.

Please set by either of the methods.

Each setting method is described in below (1) to (3).

(1) IU AD, REF AD SW settings: This section (7.1. Setting the address)

(2) Remote controller settings:

(3) Automatic address settings: Refer to the outdoor unit manual for detailed setting

En-9

CAUTION

Wrap the pipes

with cloth tape

There are no gaps

For connection from the left rear

Cable

Wall pipe

Drain hose

Putty

PROHIBITED

Accumulated

No upward

drain water

slope

50 mm or less

from ground

Refer to the wired or wireless remote controller manual

for detailed setting information. (Set IU AD, REF AD

SW to 0)

information. (Set IU AD, REF AD SW to 0)

7.1. Side panel L and control cover removal

Refer to "3.4. Side panel L, R removal and installation" to remove the side panel L.

7.2. Setting the address

Manual address setting method

The indoor unit address and the refrigerant circuit address can also be set up through the

wireless remote controller

Be sure to turn OFF the power before performing the field setting.

• Position and detail of the switches

Cable

• Please set it according to the following procedures when setting manually.

Right side of

pipe bracket

Use an insulated screwdriver to set the dip switches.

Be careful not to make mistakes for switch settings.

7.2.1 Indoor unit address

• Rotary switch (IU AD × 1)....Factory setting "0"

• Rotary switch (IU AD × 10)....Factory setting "0"

When connecting multiple indoor units to 1 refrigerant system, set the address at IU AD

SW as shown in the Table A

7.2.2 Refrigerant circuit address

Connection

pipe

• Rotary switch (REF AD × 1)....Factory setting "0"

• Rotary switch (REF AD × 10)....Factory setting "0"

In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A for

each refrigerant system.

Set to the same refrigerant circuit address as the outdoor unit.

Setting

Indoor unit ad-

Putty

dress

Refrigerant

circuit address

Air

• If working in an environment where the wireless remote controller can be used, the ad-

dresses can also be set using the remote controller.

• If setting the addresses using the wireless remote controller, set the indoor unit address

and refrigerant circuit address to "00".

(For information on setting using the wireless remote controller.)

Table A

upward

Address

slope

Refrigerant circuit

Do no t set the indoor unit address (IU AD SW) at 64 to 99. It may result in failure .

CAUTION

For indoor unit address

For refrigerant circuit

address

CAUTION

Setting range

Type of switch

Setting

0 to 63

example 2

Setting

0 to 99

example 63

Rotary Switch Setting

Address

REF AD SW

Indoor unit

× 10

× 1

IU AD × 10

IU AD × 1

REF AD × 10 REF AD × 1

Rotary Switch Setting

IU AD SW

× 10

× 1