投影スクリーン Draper 118197のPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper 118197 4 ページ。 220v ultimate access electric projection screen

ページを印刷する

220V Ultimate Access Electric Projection Screen by Draper

These Installation/Operating Instructions are available in the ofﬁ cial language

of the country where you purchase the product. Please contact your distributor

to request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

ofﬁ ziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

➀ Read in struc tions through com plete ly before pro ceed ing.

➁ Follow instructions carefully. Installation con trary to in struc tions

invalidates warranty.

➂ Entire bottom of screen case should be unobstructed to permit

access to bottom panel for electrical connections or servicing.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) and mounting brackets are packed sep a rate ly

in screen car ton. Do not discard with packing material.

➆ Screen operates on 220 V AC, 50 Hz. current.

NOTE: Screen has been thoroughly inspected and tested at fac to ry and

found to be operating properly prior to shipment.

Hanging Screen

When locating viewing surface and checking clear ance for screen's op er a tion,

remember surface is centered in the length of the case.

Screen is normally recessed above ceiling and may be installed in a variety

of ways. See typical installations detailed on page 3. Re gard less of mount ing

method used, the following points apply:

➀ Mounting brackets are packed separately in carton. Engage each

bracket with top of housing as shown below and tighten set screws. A

bracket should be within 46 cm from each end of screen case. Brackets

can be removed and case mounted with lag screws through top of case

(holes drilled on site).

➁ Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken in stal la tion.

➂ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen.

➃ Entire bottom of case must be readily accessible after in stal la tion is

complete.

➄ The bottom access panel, trap door, and lower edge of the case are

joined with continuous hinge joints and must operate freely. Front and

back of case must be straight–not forced to warp or bow. Hinge joints

Remove shipping brackets

before operating screen.

Slots along top of case permit

brackets to be set at an angle

Typical Installation

Form UltimateAccess220V_Inst09-R

Installation/Operating Instructions

Caution

Shipping

Bracket

Alternate

Installation

(additional

set of brack-

ets required

but not in-

cluded)

Case dimensions

on page 4.

Printed in U.S.A.

must be free of mastic or paint build up, and trapdoor and access panel

must be unobstructed by ceiling tiles.

➅ If case is painted on location, removal of roller/fabric assembly is

recommended prior to painting. If not removed, slots on bottom of case

should be shield ed to protect view ing surface from paint splatters or

overspray.

➆ Do not seal unit in ceiling until elec tri cal con nec tions have been made

and screen has been op er at ed successfully.

Screen operates on 220 V AC, 50 Hz. cur rent.

Junc tion box is lo cat ed just above the bottom access panel at left end of

screen.

Open the access panel/trap door for access to the junction box cover. (See

bottom access panel/trap door opening and closing instructions below).

Remove two (2) hex head screws that secure the cover to the junction box to

expose the terminal strip per wiring diagram on page 4.

If optional low voltage control or video interface control is speciﬁ ed and factory

installed, please refer to wiring diagram on page 4.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is connected.

Bottom Access Panel/Trap Door Opening & Closing

After screen case has been mounted, remove the dowel shipping brackets

from dowel if provided. A spring latch at each end of the trap door holds

this assembly closed. In some screens there will also be a spring latch

near the center of the case. To gain access to inside of screen case, disen-

gage spring latch at each end of the case (and near the center of the case, if

applicable) by sliding the latch lever towards the center of screen case, then

pull down slightly on the trap door assembly. The latch levers are somewhat

concealed from view. Locate these with the trap door open by feeling for the

vertical latch lever above the door about 8 cm from case endcaps and near

the center of the case.

The assembly will swing down, opening about 135°. Pivot the prop arms at

each end of the trap door assembly towards the ends of screen case. Prop

arms engage with a hole in each endcap to hold the trap door assembly fully

open. To close the trap door assembly disengage prop arms from endcaps

and pivot these over the access panel. Swing the trap door as sem bly upward,

stopping just before the latch levers hit the bottom ﬂ anges of the endcaps

(and center of case where appropriate). Pull levers of latches towards center

of screen case to allow the trap door assembly to be pivoted to its closed po-

Dowel

sition. Make sure that the spring latch levers engage fully with case endcaps

(and center of case where appropriate).

If you encounter any difﬁ culties installing or ser vic ing your Ultimate Access screen, call

your dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-1689.

Electrical Con nec tions