投影スクリーン Draper 220V AccessのPDF 設置および操作説明書をオンラインで閲覧またはダウンロードできます。Draper 220V Access 4 ページ。 Electric projection screen

ページを印刷する

220V Access Electric Projection Screen by Draper

These Installation/Operating Instructions are available in the ofﬁ cial language

of the country where you purchase the product. Please contact your distributor

to request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

ofﬁ ziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

① Read instructions through completely before proceeding; keep them

for future reference. Follow instructions carefully. Installation con trary to

instructions in val i dates warranty. Care in mounting and correct operation

will mean long and satisfactory service from your Draper screen.

② Allow enough access to remove front cover should fabric be come

damaged or should other service be required.

③ Screen should be installed level (using a carpenter's level).

④ Nothing should be fastened to screen dowel or viewing surface

⑤ Operating switch (es) is packed separately in screen carton. Do not

discard with packing material.

⑥ Screen operates on 220V AC, 50 Hz., 1ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

When locating viewing surface and checking clear ance for screen operation,

remember surface is centered in the length of the case. Regardless of

mounting method used, the following points apply:

① Mounting brackets are shipped attached to the case. Engage each bracket

with top of housing as shown below and tighten set screws. A bracket

should be within 46 cm of each end of screen case. Brack ets can be

removed and case mounted with lag screws through top of case (holes

drilled on site).

② Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken in stal la tion.

③ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Supporting hardware (chains,

cables, rods, etc.) must be essentially vertical.

④ Entire bottom of case must be readily accessible after in stal la tion is

complete.

Remove

shipping

brackets

Shipping

Bracket

before

operating

screen.

Typical

Installation

Case dimensions

on page 3.

Form Access220V_Inst10-R2 Printed in U.S.A

Installation/Operating Instructions

Caution

Dowel

Slots along top of case permit

brackets to be set at an angle

⑤ Front, back and top of case must be straight—not forced to warp or bow.

⑥ If case is painted on location, removal of roller/fabric assembly is

recommended prior to painting. If not removed, slot on bottom of case

should be shield ed to protect view ing surface from paint splatters or

overspray.

⑦ Do not seal unit in ceiling until elec tri cal con nec tions have been made and

screen has been op er at ed successfully.

Screen operates on 220V AC, 50 Hz., 1 ph cur rent.

Junction box is lo cat ed just above the bottom access panel at left end of

screen (stan dard, right end may be speciﬁ ed).

Remove the bottom access panel for access to the junction box cover. (See

Bottom Access Panel Removal instructions below). Remove four (4) hex head

screws that secure the cover to the junction box to expose the blue, brown

and black pigtail leads and the green ground wire (if they aren't already exiting

the case via the cable knockout) per wiring diagram on page 3.

If optional low voltage control or video interface control is speciﬁ ed and factory

installed, please refer to wiring diagrams on page 4.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is connected.

Bottom Access Panel Installation/Removal

Bottom access panel hooks over the lower in side edge of the screen hous ing

and then is pivoted downward until the engagement brackets on each end of

the bottom panel click into place with the ball detents on each endcap. Make

sure bottom access panel clicks in place at each end of its length.

Remove bottom access panel by pushing up at each corner of panel ad ja cent

to slot in bot tom of the hous ing.

With bot tom ac cess panel an gled up ap prox i mate ly at 20° it can be lift ed off of

the lip of the housing and then lowered out of the housing completely.

With bottom access panel

angled up approx. 20 degrees,

engage hook on the panel

with lip of the housing

Alternate

Installation

(additional

set of

brackets

required but

not included)

If you encounter any difﬁ culties installing or ser vic ing your Access screen, call your

dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-1689.

Electrical Con nec tions

Using the hook and lip as a pivot,

pull the panel downward until the

engagement brackets click into

place with the ball detent

on each endcap

Engagement bracket

(one on each end of the

bottom access panel)

Bottom flange of Access housing

Bottom access panel pushup

points for panel removal

Caution: Beware of pinch

points at ends of closure

Access case as seen from below

US Patent Nos.

6,137,629; 6,421,175;

6,532,109; 6,816,308;

7,559,707