- ページ 2

投影スクリーン Draper Access XLのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Access XL 5 ページ。 Draper access xl electric projection screen
Draper Access XL にも：取付・取扱説明書 (5 ページ), 取扱説明書 (8 ページ)

ページを印刷する

Access XL Instructions by Draper

2 Disengage closure from extrusion inside the case. Rotate closure as

shown in Fig. 4 and remove, holding it so the closure remains in this posi-

tion and does not bow before placing it on a flat surface.

Bottom flange of Access XL housing

Bottom access panel pushup

points for panel removal

Caution: Beware of pinch

points at ends of closure

Access XL case as seen from below

Accessory Access ACXLE & ACXLV Roller Installation

Please note: When ordering a motor with built-in Low Voltage Controller, if

the case ships separate from the "guts," the case includes the 25' cable and

special low voltage switch.

1 Remove the bottom access panel (see "Bottom Access Panel Installation/

Removal" section above).

2 The motor end mounting bracket has a metal bracket with snap ring for

accepting motor head. The idler end mounting bracket has spherical ball

bearings for accepting the idler pin. Both brackets have four set screws that

will be used to tighten the brackets in place inside the case. Back out the

four set screws in bracket until they are flush with top side of bracket, then

remove the roller assembly from the shipping brackets, placing the roller

assembly on a flat, clean surface (see Fig. 5).

Shipping Brackets

Motor End (Series V shown)

Please Note: Do not lose the snap ring and screw from the motorized

end, or the eight nylon washers, spring lock washer, fender washer and

machine screw from the idler end. They are required for re-attaching the

roller assembly to the brackets inside the case.

3 To engage the motor end bracket flange above the two channels in the top

of the screen housing, rotate the bracket approximately 45° counter-

clockwise to allow the top surface of the motor bracket to rest flat against

the top inside of the housing. Rotating the bracket clockwise until it is

engaged with the mounting channel, slide it along the length of the housing

against the electrical junction box. Note: Set screw collar side of the bracket

must point toward the center of the case.

Caution: Do not allow the bracket to rotate and fall out of the channel.

4 Tighten all four set screws.

Figure 4

Carriage

Bolt

Idler End (Series E shown)

Figure 5

www.draperinc.com

5 Replace the eight Nylon Washers into the idler end of the roller assembly.

6 Loosen the carriage bolts which attach the flange-mounted bearing to the

idler end bracket just enough to allow the bushing some limited movement,

which will help when installing the roller assembly.

7 Rotate the bracket into the mounting channel located in the case top (when

mounting the roller assembly into the case). Both the bracket flange and set

screw collar side of the bearing must point toward the gudgeon assembly.

8 Raise the roller/fabric assembly up into the screen housing and engage the

head of the motor completely into the motor mounting bracket, making sure

the snap ring engages with the motor and that the limit switch adjusting

knobs are visible from the bottom of the screen housing (see Fig. 6).

Please note: Maximum torque for

tightening screw is 6.77 Nm.

Figure 6

Caution: When placing the roller assembly into the case, be sure

motor is fully re-seated in the bracket, and secure it carefully with the

motor retaining spring and screw. Limit adjustment screws should be

facing down to allow access to them.

Caution: Due to the weight of the roller assembly, this step requires at

least two people to perform safely.

9 While supporting the idler end of the roller, slide the idler end mounting

bracket toward the roller. Slide the bearing over the end of the shaft.

Caution: Do not allow bracket to rotate and fall out of channel!

Align the bracket into the housing and tighten all four of the set screws.

Lock the roller assembly into place on the mounting bracket with the fender

washer, spring lock washer and machine screw (see Fig. 7).

10 Re-tighten the carriage bolts in the Idler-end Bracket Assembly so that the

flange-mounted bearing is locked in place (see Fig. 5).

Idler End

Roller Bracket

Setscrews

8 Nylon

Washers

Roller

Gudgeon

Assembly

11 Tighten the two set screws in the bearing collar.

12 Connect electrical plug from motor to mating socket on junction box.

13 Reinstall the bottom access panel as previously described (see Figs 3 & 4).

Motorized Roller/Fabric Removal

Reverse the instructions above "Motorized Roller/Fabric Installation" for

removal of the unit.

Operation

When screen is first operated, be cautious! Cycle unit down and up several

times to confirm satisfactory operation.

110-120V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

110-120V MULTIPLE STATION CONTROL—Switches are similar in

appearance to 110-120V Single Station Control. Screen stops when switch

is released and may be restarted in either direction. Factory adjusted limit

switches stop screen automatically when fully down or fully up.

24V CONTROL—Three-button UP-STOP-DOWN switches stop at any

point desired, operate in any sequence. Factory adjusted limit switches

automatically stop screen when fully down or fully up. Installer should

incorporate an all-pole disconnect in the fixed wiring.

110-120V & 12V VIDEO INTERfACE CONTROL—Allows screen to be

controlled by trigger signal (100 milliAmp minimum)—when the signal comes

on, the screen descends automatically. Two versions: Model VIC115 integrates

screen operation with a Draper video projector lift or a video projector or

(765) 987-7999

page 2 of 5

Setscrews

Fender

Bearing

Washer

Collar

Machine

Screw

Spring

Lock

Washer

Carriage

Bolts

Figure 7