投影スクリーン Draper EnvoyのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Envoy 2 ページ。 Electric projection screen
Draper Envoy にも：取付・取扱説明書 (3 ページ), 取付・取扱説明書 (3 ページ), 取付・取扱説明書 (3 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (3 ページ)

ページを印刷する

Read instructions through completely before proceeding.

Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

Entire bottom of screen case should be unobstructed to permit proper

operation of automatic trap door, and access to bottom panel for making

electrical connections or servicing.

Screen should be installed level (using a carpenter's level).

Nothing should be fastened to screen dowel, viewing surface or

automatic trap door.

Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

Screen operates on 115 v., 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

General:

When locating viewing surface and checking clearance for screen's

operation, remember surface is centered in case. Screen is normally

recessed above ceiling and may be installed in a variety of ways. See typical

installation detailed on back of this sheet. Regardless of mounting method

used, the following points apply:

Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken installation.

Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen.

Entire bottom of case must be readily accessible after installation is

complete.

Hinge on bottom board and particularly hinge on automatic trap door of

screen must be permitted to operate freely. Front and back of case must

be straight—not forced to warp or bow. Hinges must be free from mastic or

paint buildup, and doors must be unobstructed by ceiling tiles.

Do not use screen case to support adjacent sections of ceiling.

If trim pieces must be attached to case, do not permit screws to protrude

through ¾" wall of case. Do not attach trim with nails.

If case is painted, slots around doors should be shielded to protect viewing

surface from paint splatters or overspray.

Do not seal unit in ceiling unit electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 115 v., 60 hz. current.

Junction box is located just above bottom board near left end of screen.

Bottom board is held closed with flathead screws and may be opened with a

Phillips screwdriver. (Automatic trap door is held shut by viewing surface and

must not be forced open.) Removal of junction box cover plate exposes red,

black and white pigtail leads and green internal ground wire per wiring

diagram attached.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with National and

local electrical codes.

All operating switches should be "off" before power is connected.

411 S. Pearl St., Spiceland, IN 47385 USA 765-987-7999 fax 765-987-7142

e-mail [email protected]

Installation/Operating Instructions

Envoy Electric Projection Screen by Draper

Caution

www.draperinc.com

Form Envoyi00R

When screen is first operated, be cautious! If automatic trap door does not

drop open immediately when switch is flipped "down", return switch to "off"

and free trap door and/or recheck electrical connections before proceeding.

Cycle unit down and up several times to confirm satisfactory operation.

115V Single Station Control — 3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

115V Multiple Station Control —Switches are similar in appearance to

115V Single Station Control. Screen stops when switch is released and may

be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully up or fully down.

24V Control — Three-button up-stop-down switches stop at any point

desired, operate in any sequence. Factory adjusted limit switches

automatically stop screen when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are

optionally available with this unit.

controls power to the screen and switches. When it is "off", the switches will

not operate screen. Key may be removed from the switch in either "on" or "off"

position.

A three-position key switch permits the screen to be operated

directly by key. In this case, the screen's operator must always have a key.

Screen has been factory set and should not normally require further

adjustment. However, if you desire to change the "up" and "down" stopping

positions, proceed as follows:

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

Adjusting "fully up" position — "Up" limit switch, located immediately

above left end of automatic trap door, is tripped as door closes. If door does

not close fully, limit switch should be raised slightly. If door closes too tightly,

switch should be lowered slightly.

Remove steel plate attached to threaded neck of "up" limit switch by

removing hex nut securing it. Removing plate exposes three Phillips head

machine screws which hold limit switch bracket in place. Turning these

screws clockwise will raise limit switch; turning them counterclockwise will

lower it.

Raise switch only in quarter-turn increments. When operating properly

automatic trap door should close gently and rest against but not press on

rubber bumpers above it. Adjusting automatic door so that it closes too tightly

will damage screen.

Adjusting "fully down" position — "Down" stopping position may be

adjusted by turning the white limit switch adjustment socket. The white socket

is located on the left end of screen roller and is accessible to a screwdriver/

Allen wrench (4mm or

easier when bottom board is also open. (Do not adjust the yellow socket

which is next to and in back of the white socket). Turning the white socket

counterclockwise will allow viewing surface to run farther down. Turning it

clockwise will shorten the viewing surface, stopping it in a less extended

position. At no time should viewing surface be unrolled enough to expose

any part of screen roller.

If you encounter any difficulties installing or servicing your Envoy screen,

call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999, fax

(765) 987-7142, or e-mail [email protected].

Printed in U.S.A.

Operation

The key-operated power supply switch

Adjustments

") when automatic trap door is open. Access is