- ページ 2

投影スクリーン Draper FlexShadeのPDF 説明書インストールと操作をオンラインで閲覧またはダウンロードできます。Draper FlexShade 12 ページ。 Exterior clutch-operated shade
Draper FlexShade にも：インストレーション＆オペレーションマニュアル (8 ページ), インストレーション・インストラクション (2 ページ), 取扱説明書 (12 ページ), 取付・取扱説明書 (11 ページ), 説明書インストールと操作 (16 ページ), 説明書インストールと操作 (4 ページ), 取扱説明書 (7 ページ), 説明書インストールと操作 (12 ページ), 説明書インストールと操作 (16 ページ)

ページを印刷する

Dual Roller Coupled Motorized FlexShade

PLEASE READ - Important Installation Information

Caution:

1. Inspect all boxes to ensure you have received the proper shades and parts.

Controls may be shipped separately, or in same carton as shades.

2. Open cartons lengthwise.

3. Before mounting shades, verify measurements on label provided with shade,

and ensure unit is installed at correct width.

4. Before connecting switches, controls, or electrical, ensure that power is

turned OFF. Wiring indicated in diagram by dashed lines must be completed

by an electrician.

PLEASE READ - Safety Information

Important Safety Information

Improper installation and use of the Dual Roller Fascia Coupled FlexShade

due to imprecise installation, mishandling of the unit during installation or installation on an insufficient wall or ceiling structure. Please use extreme care.

1. Please read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail, and could

result in serious injury.

2. Installation and calibration of the unit should only be performed by an

authorized, qualified, and experienced professional. In particular, electrical work

and wiring [indicated in diagram by dashed lines] must be completed only by a

qualified professional electrician who has read this manual completely and is

familiar with the construction and operation of this equipment and the hazards

involved.

3. Do not affix the unit to wall or ceilings that have inadequate strength to

permanently hold the unit during use. It is the owner's and installer's

responsibility to confirm the wall or ceiling to which the unit attaches is

sufficient to permanently hold the weight and stress loads of the unit at all times.

Draper

, Inc., is not responsible for improper installation, application, testing, or

workmanship related to the product at place of installation.

4. It is the installer's responsibility to ensure appropriate fasteners are used for

mounting.

5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware must be

installed level. Unit must be level and square.

6. Never leave the area while operating the unit during installation, maintenance, or

normal operation, unless it is secure and safe.

7. Before testing or operation, carefully inspect the entire area and path of the

shade and areas underneath the shade to be sure no persons or objects are in

the area.

8. Turn off power and any nearby equipment or cables carrying electricity before

connecting switches, wires, controls, or electrical components.

1. Look for any job site conditions that could interfere with installation or operation

of the system.

2. Read carefully and be sure to understand all installation instructions and all

related operations manuals. These instructions are intended to serve as a guide

for the installer and owner. They should be followed closely and combined with

the expertise of experienced qualified installers. Draper, Inc., is not responsible

for improper installation, application, testing, or workmanship related to the

product at place of installation. Please retain all instructions for future use.

PLEASE READ - Field Adjustments

Each Draper

Solar Control Shade is tested to ensure

proper operation. Even with this testing, some field

adjustments may be needed for telescoping.

If the shade is telescoping, place a piece of high quality

gaffer tape about 1"

wide on the exposed roller

(25 mm)

on the side that the fabric will

(where the fabric will cover it)

be drawn toward. For example: if the fabric is tracking

to the left, place the tape on the right side.

5. Do not wire motors in parallel without written permission from Draper.

6. All brackets, fascia, pocket headbox, and other hardware must be installed

level. Shades must be level and square.

7. Read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail,

and invalidates warranty.

8. Installer is responsible for selecting mounting hardware appropriate for

site conditions.

WARNING

can result in serious injury or death. Primarily, injuries can occur if the unit falls

9. Ensure the limit switches are pointed down or accessible when placing the

motor in brackets/endcaps.

10. All motors should be tested and limits set using test cord before shades are

wired.

11. Do not wire motors in parallel without written permission from Draper, Inc.

12. During testing or operation, carefully watch the surrounding area for any

potential safety concerns including nearby persons or objects.

13. After installation, the entire system, including all sensors, should be carefully

tested to ensure safe and normal operation. Extreme care should be taken

during testing to remain clear of moving parts to avoid possible injury.

14. Operation of unit should be performed only by authorized and qualified

personnel, who have been trained in the safe and effective operation of the unit

and understand its safety features.

15. The safety features of the unit , including sensors, should never be disabled,

bypassed, or overridden. The system should not be operated until all safety

features, including the sensors, are properly and completely installed,

calibrated, and tested.

16. Unit may need to comply with local, state, or district rules and regulations, in

particular when installed in schools. All applicable rules and regulations should

be reviewed before installation and use.

17. Failure to precisely follow installation guidelines invalidates all warranties.

18. Custom products/installations may not be reflected in this manual. Call Draper,

Inc., if you have questions about the installation of custom products or any

questions about your installation.

Before Beginning Installation

3. Open cartons lengthwise.

4. Locate and lay out all pieces.

5. Inspect all boxes to ensure you have received the proper shade and parts.

Controls may be shipped separately, or in same carton as shade.

6. If you have any difficulties with installing, servicing, or operating your shade, call

your dealer or Draper, Inc., 765-987-7999.

PLEASE READ - Cleaning and Maintenance

Window covering products manufactured by Draper

operational maintenance or lubrication.

Most standard Draper

fabrics may be cleaned at the window by vacuuming with a soft brush

attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy

water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish.

Please Note: Exceptions are Flocké and Phifer SW7000

sponge. SheerWeave

is a registered trademark of Phifer

(Extra Large Hardware)

Important Safety Information

, when properly installed, should require no

fabrics, which must be cleaned with a dry art

Incorporated.

page 2 of 12