- ページ 4
投影スクリーン Draper FoundationのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Draper Foundation 17 ページ。 Foundation for led panels
ページを印刷する
Foundation
for LED Panels
™
Section 3 - Determining Horizontal Mounting Location
Section 3.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
The Foundation Wall Brackets must be securely anchored to the wall. If mounting to drywall/gypsum board wall, all mounting hardware
anchored to a vertical stud. If mounting to a brick or block wall, the brackets must be evenly spaced no more then 32"
in this manual, the bracket spacing is 24" unless specified otherwise.
The example below is for a 6 x 6 Array. Other standard 2 rail array sizes
1. Mark the location of the
Bottom Left Corner
of the
viewing
area.
22 1/16
2. From the mark made in step 1, measure up
(561mm)
and draw a level horizontal line the width of the LED display.
This is the top mounting hole location of the
WALL MOUNTING BRACKET FOR THE BOTTOM HORIZONTAL RAIL
3. From the mark made in step 1, measure up
78 7/8"
and draw a level horizontal line the width of the LED display.
(2004mm)
This is the top mounting hole location of the
WALL MOUNTING BRACKET FOR THE TOP HORIZONTAL RAIL
For 4x4 or 5x5 arrays, use the chart at right to determine the proper value for
The fully assembled Horizontal Rails
will be hung from them in Section 5.
(see section 4)
Fig. 3.1
Overall Width with Trim: 142
Image Width: 141
13
/
TOP RAIL
16
MOUNTING
HARDWARE
78
7
/
"
8
(2004mm)
or
DIM A
from Chart Above
PLEASE NOTE:
END OF HORIZONTAL RAIL
to be
no more than 16"
from the
(406mm)
CENTER
of the OUTER Wall Brackets
BOTTOM RAIL
MOUNTING
HARDWARE
22
/
"
1
16
(560mm)
LOCATION of
BOTTOM LEFT
LED Cabinet
START HERE
Image Area
LOCATE BOTTOM LEFT of
or
Trim
LOCATE BOTTOM LEFT of
(by others)
apart. In the drawings showing
(813mm)
are shown in the table at right.
(4x4 & 5x5)
(see Mounting Bracket Detail at right)
(see Mounting Bracket Detail at right)
Dim
A.
/
" (3627mm)
13
16
" 3602mm)
6 x 6 Array Shown
Refer to chart above for
mounting dimension specific
to 4x4 and 5x5 Systems
NOTE: If installing trim, you must allow 1
5
/
" (33mm) of clearance around the outside of the image area.
16
page 6 of 32
STANDARD ARRAY MOUNTING DIMENSIONS
must be
Array
Vertical distance from Bottom Left of to Top
Size
Rail Mounting Hardware
4x4
5x5
.
6x6
.
BOTTOM RIGHT
Foundation
for LED Panels
™
DIM A
FINAL VIEWING AREA
HEIGHT
WIDTH
94 1 / 2 "
52 11/ 3 2"
53 1/ 8 "
(1329mm)
(1350mm)
(2400mm)
65 5/ 8 "
66 5/ 1 6"
118 1/ 8 "
(1667mm)
(1688mm)
(3000mm)
78 7 / 8 "
79 7 / 8 "
141 7/ 8 "
(2004mm)
(2025mm)
(3600mm)
Ø
Ø
(Ø20mm)
Image
Height
79
"
/
7
8
(2025mm)
Overall
Height
80
"
/
13
16
(2052mm)
LOCATION of
LED Cabinet
page 7 of 32
Mounting
5
/
"
Hardware
16
(Ø7mm)
LASER LINE
/
"
(Ø14mm)
9
/
"
16
13
16
MOUNTING
BRACKET
DETAIL