- ページ 4

投影スクリーン Draper Paragon EのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Paragon E 7 ページ。 Large, ceiling-recessed screen designed for auditoriums and lecture halls.

ページを印刷する

Paragon E & V

Section 2 - Electrical Connections

1. Screen operates on 110-120V, 60 Hz., 1.1 amp

current draw.

2. Junction box is located just above the bottom

access panel at the left end of the screen.

3. Open the access panel/trap door for access to

the junction box cover.

(See bottom access panel/

trap door opening and closing instructions below)

Section 3 - Operation

CAUTION: When operating for the first time, cycle unit down and up several times to confirm satisfactory operation. Be prepared to cut POWER if necessary.

•

110-120V SINGLE STATION CONTROL - 3-position UP-OFF-

DOWN switch permits operation to be stopped at any point. Factory

adjusted limit switches automatically stop screen when fully down

or fully up.

•

24V CONTROL

(optional and requires optional LVC-IV)

STOP-DOWN switches stop at any point desired and operate in

any sequence. Factory adjusted limit switches automatically stop

screen when fully up or fully down. Installer should incorporate an

all-pole disconnect in fixed wiring available with RF or IR remote.

Section 4 - Limit Adjustments

Please Note: Screen limits are factory set. Instructions below for minor adjustments only. Please check with Draper prior to resetting screen limits.

CAUTION:

- Be sure all switches are in "off" position before

adjusting limit switches.

- Be prepared to shut off manually while testing.

- Screen may be damaged by lowering it too far and

exposing roller.

- Motor must be installed so that limit switches are

pointed down.

CAUTION:

Rough handling in transit may cancel/reset motor limit

settings. To prevent viewing surface damage, be

prepared to stop descending screen if surface begins

to retract instead of stopping or if motor does not shut

off when screen has fully retracted into case.

4. Remove two

hex head screws that secure

(2)

the cover to the junction box to expose the red,

black, and white pigtail leads and the green

ground wire per wiring diagram

5. If optional low voltage control or video interface

control is specified and factory installed, please

refer to wiring diagram

- 3-button UP-

ADJUSTING "FULLY UP" POSITION:

1. Place small screwdriver in groove of yellow button on motor and press vertically until it

"clicks."

2. Raise screen by pressing UP switch. Press STOP switch when screen reaches desired

position. Then press yellow button on motor until hearing a "click", then release.

ADJUSTING "FULLY DOWN" POSITION:

1. Place small screwdriver in groove of yellow button on motor and press vertically until it

"clicks."

2. Lower screen by pressing DOWN switch. Press STOP switch when screen reaches desired

position. Then press white button on motor until hearing a "click", then release.

CAUTION: AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE

ANY PART OF SCREEN ROLLER

6. Screen is shipped with internal wiring complete

(Page 7)

7. All operating switches should be "off" before

•

RS232 / ETHERNET - Serial communication and network

communication optionally available.

•

KEY OPERATED SWITCHING - Two key-operated switches optionally

available with this unit:

•

Key-operated power supply switch controls power to screen a

and switches. When "off", switches will not operate screen. Key may

be removed from switch in either "on" or "off" position.

•

Three-position key switch permits the screen to be operated directly

by key. Requires screen operator to have a key.

page 4 of 7

and control switch

fully boxed. Wire to connect

(es)

screen to switch

and switch

(es)

should be furnished by installer. Connections

should be made in accordance with attached

wiring diagram, and wiring should comply with

national and local electrical codes.

power is connected.

to power supply