投影スクリーン Draper PremierのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Premier 4 ページ。 220v premier electric projection screen
Draper Premier にも：取付・取扱説明書 (2 ページ), 取付・取扱説明書 (2 ページ), インストレーション・インストラクション (2 ページ), 説明書インストールと操作 (7 ページ), インストレーション・インストラクション (4 ページ), インストレーション・インストラクション (2 ページ), インストレーション・インストラクション (2 ページ), 据付・取扱説明書 (7 ページ)

ページを印刷する

Targa and Premier Electric Projection Screens—Large Sizes by Draper

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invali-

dates warranty.

3 Screen should be accessible for complete removal should fabric be-

come damaged or should other service be required.

4 Screen should be installed level (using a carpenter's level). The case

must also be installed so that the top of the case is level (front-to-back)

to prevent the fabric from contacting the case housing.

5 Nothing should be fastened to screen dowel or viewing surface.

6 Operating switch(es) packed separately in screen carton.

Do not discard with packing material.

7 Screen operates on 110-120V, 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Hanging Screen

General:

Screen should be lifted into position only by the end mounting brackets.

Keep case level by lifting end plates simultaneously to prevent surface

damage. Never attempt to lift screen along its length.

Installer must also insure that wall or ceiling structure is of adequate

strength. Supporting hardware must be essentially vertical. Do not suspend

this product using chain or cable unless also using Targa /Premier (Large

Case) Direct Cable Kit. The screen must be securely fastened using at

least two of the mounting holes provided in each of the case mounting

brackets.

When locating viewing surface and checking clearance for screen's

operation, remember surface is centered in case. Handle case carefully to

protect its finish.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Ceiling and Wall Installation:

Product is very heavy: Installer must provide adequate attachment

hardware and anchors as required. Installer must also insure that the

structure is of adequate strength.

Please Note: Large size Targa and Premier

screens ship with brackets installed to help hold

fascia in place. These brackets (shown to the right)

must be removed if you wish to remove the fascia.

Case must be mounted low enough from ceiling to

gain access to bracket screws.

Caution: If you remove the brackets, remem-

ber to re-install them when you put the fascia

back on!

Caution: Do not remove the roller

assembly from the case unless

necessary for repairs. If the roller

assembly is removed, be sure motor

is fully re-seated in the bracket, and

re-secure it carefully with the motor

retaining spring and screw

(see diagram at right).

Screw is included with Large

Targas and Large Premiers.

Please note: Do not use a power screwdriver to tighten screw.

Maximum torque for tightening screw is 5 lb-inches.

Installation/Operating Instructions

Caution

Printed in U.S.A.

Electrical Connections

Screen operates on 110-120V, 60 Hz. current. Screen is shipped with internal

wiring complete and control switch(es) fully boxed, and standardly supplied

with a 6' cable lead. Longer lead can be substituted by removing two screws in

motor end of roller, removing lead, plugging new lead in, and replacing screws.

Wire to connect screen to switch(es) and switch(es) to power supply should

be furnished by installer. Please Note: Screen must be installed in accordance

with the requirements of the Local Building Codes, the Canadian Electrical

Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA

70. An appropriate disconnect device shall be provided as part of the building

installation.

All operating switches should be "off" before power is connected.

Plug-in power cord option available with built-in low voltage motor.

For Reconfiguration/Conversion of Non-detachable Power Cord to

Field Wiring for Models PRE-28, PRE-29, PRE-30, TAR-28 TAR-29 and TAR-

30 Only:

1 Disconnect cord plug from outlet.

2 Remove junction box cover.

3 Disconnect wire nuts from black, white and green wires.

4 Remove power cord and strain relief from screen.

5 Connect the black motor wire to "hot" supply wire.

6 Connect white motor wire to "neutral" supply wire.

7 Connect green/yellow wire to "ground" supply wire.

8 Replace junction box cover.

Before fully operating screen: On Large Targa, remove tape; on Large Premier,

lower viewing surface enough to fully expose shipping brackets, then remove

shipping brackets by loosening screws, removing end shipping brackets, sliding

center shipping brackets off dowel, and re-tightening screws (see diagram).

110-120V Single Station Control — 3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches automati-

cally stop screen when fully down or fully up.

110-120V Multiple Station Control — Switches are similar in appearance to

110-120V Single Station Control. Screen stops when switch is released and

may be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully down or fully up.

24V Control — Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop

screen when fully down or fully up.

Key Operated Switching — Two kinds of key-operated switches are option-

ally available with this unit. 1 The key-operated power supply switch controls

power to the screen and switches. When it is "off ", the switches will not operate

screen. Key may be removed from the switch in either "on" or "off" position. 2

A three-position key switch permits the screen to be operated directly by key. In

this case, the screen's operator must always have a key.

RS232/Ethernet — Serial communication and network communication

optionally available with wall switches, RF or IR remote.

Plug & Play

— Provided with handheld IR remote control transmitter and

10' (3m) cord. No wiring necessary except to connect to RS232. Screen is

equipped with a handheld remote or 3-position operating switch (see below).

Three positions (up-off-down) permit operation to be stopped at any point.

Factory adjusted limit switches automatically stop screen when fully down or

fully up.

If you encounter any difficulties installing or servicing your Targa or Premier screen, call

your dealer or Draper Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Operation

Continued on page 2