- ページ 4

投影スクリーン Draper Premier XLのPDF 説明書インストールと操作をオンラインで閲覧またはダウンロードできます。Draper Premier XL 8 ページ。 Electric projection screen 220v

ページを印刷する

Premier XL / Targa XL 220V

Section 5 - Limit Adjustments

Figure 9

Please Note: Screen limits are

factory set. Instructions below

for minor adjustments only.

Please check with Draper prior

to resetting screen limits.

Please Note: If screen is "Right

Hand Motor," the WHITE/

DOWN

and YELLOW/UP

(I)

(II)

limit screws are reversed

(Fig.

10)

CAUTION:

- Be sure all switches are in "off"

position before adjusting limit

switches.

- Be prepared to shut off manually

while testing.

Figure 10

Motor

End

d i e

A u

S i d

Standard Roll

Left hand motor:

White Socket—Down

Yellow Socket—Up

Right hand motor:

White Socket—Up

Yellow Socket—Down

Section 5.2 - Limit Adjustments for Motors with Internal Low-Voltage Controllers

Please Note: Hold STOP button for 3-5 seconds while in programming mode to reverse motor direction.

Figure 11

BACK VIEW OF WALL SWITCH

To Motor

with

Internal

Low Voltage

Slide

Switch

To Motor

with

Internal

Low Voltage

POSITION

FUNCTION

DOWN

Set LOWER limit

Set UPPER limit

CENTER

Normal Operation

Please Note: 5V DC must be connected to

be able to set limits using the wall switch.

DOWN Limit

DOWN Limit (I)

Clockwise

Clockwise decreases

decreases

down travel.

UP Limit (II)

UP Limit

Counterclockwise

increases up travel.

- Screen may be damaged by

lowering it too far and

exposing roller.

- Motor must be installed so that

limit switches are pointed down.

Motor

End

n c

c k

B a

d e

S i

Reverse Roll

Left hand motor:

White Socket—Down

Yellow Socket—Up

Right hand motor:

White Socket—Up

Yellow Socket—Down

1. Connect internal low-voltage switch to motor via terminal

blocks, or via modular port using a four conductor modular

cable. When using modular cable, cable connectors MUST

NOT be crimped in reverse, as with standard telephone

cable.

(For Dry Contacts Wiring Diagram, see Section 8.)

2. Set slide switch to lower position. Hold DOWN button

to move viewing surface to desired lower limit. If screen

moves in opposite direction, release DOWN button and hold

STOP button for 4 seconds. This reverses operation of UP

and DOWN switches.

3. Move slide switch into center position. Wait several seconds.

Please Note: Do Not move slide switch from DOWN to UP

in one motion. This will set limits in same position.

4. Set slide switch to higher position. Move viewing surface to

desired upper limit by holding UP button on wall switch.

5. Return slide switch to center position to resume normal

operation.

6. To set viewing surface to alternate format position, move

viewing surface to desired position and press STOP button.

Hold STOP button for at least 3 seconds to record position.

Section 5.1 - Standard Motors

(I)

Section 5.1.1 - "Down" Limit Adjustment

To Reduce Screen Drop:

1. Raise screen surface approximately 1'

and turn off.

2. Turn DOWN

3. Test by lowering screen. Repeat steps 1 & 2 until desired position is

reached.

To Increase Screen Drop:

(II)

1. Lower screen to down limit.

2. With down switch on, turn DOWN

(3 screw turns = 1/2 roller revolution)

3. Test by raising screen approximately 1'

down limit.

4. Repeat steps 2 and 3 until desired position reached.

Section 5.1.2 - "Up" Limit Adjustment

If Screen Raises Too High:

1. Lower screen surface approx. 1'

2. Turn UP

limit screw clockwise

(II)

Motor

3. Test by advancing screen up.

End

4. Repeat steps 1 through 3 until desired position is reached.

n c

If Screen Needs to Raise Higher:

d i e

A u

1. Lower screen surface approx. 1'

S i d

2. With UP switch on, turn UP

(3 screw turns = 1/2 roller revolution)

3. Repeat steps 1 and 2 until desired position is reached.

Waterfall Roll

CAUTION: DO NOT allow dowel to wrap over roller when operating screen!

Left hand motor:

This could damage screen.

White Socket—Up

Yellow Socket—Down

Right hand motor:

White Socket—Down

Yellow Socket—Up

(Fig. 11)

(Fig. 9)

(requires 5/32" (4 mm) hex key wrench)

above desired setting

(30 cm)

limit screw clockwise

(I)

(3 screw turns = 1/2 roller revolution)

limit screw counterclockwise

(I)

to increase drop.

(30 cm)

below desired setting and turn off.

(30 cm)

(3 screw turns = 1/2 roller revolution).

below desired setting and turn off.

(30 cm)

limit screw counterclockwise

(II)

Please Note: Press and release UP

button on switch to move screen to

upper limit. Press and release DOWN

button to move screen to lower limit.

• While motor is in motion, press

STOP button for less than 2

seconds to stop viewing surface at

present position.

• Once motor is stopped, press

STOP button to move viewing

surface to alternate format position.

• Hold STOP button, when motor is

at rest or in motion, for 3-5

seconds to record new alternate

format position.

• Hold STOP button for 3-5 seconds

while in programming mode to

reverse motor direction.

page 4 of 8

then down to new