- ページ 2

投影スクリーン Draper Series EのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Series E 4 ページ。 Electric projection screen
Draper Series E にも：取付・取扱説明書 (4 ページ)

ページを印刷する

220V Silhouette/Series E & V by Draper

To mount suspended from ceiling, the brackets need to be installed on

screen case as noted on page one. Attach "S" Hooks (supplied) through the

holes in the brackets. Select the set of holes that allows the screen to hang

in a vertical position. The installer is to provide the materials and fasteners

to attach the "S" Hooks to the ceiling. Installer must insure that the fasteners

and suspension material is of adequate strength and suitable for the mounting

surface chosen.

Mounting on 15 cm extension wall brackets: 15 cm or 25-36 cm brackets

are needed to mount Silhouette ex tend ed from wall. Brackets are not supplied

with screen and must be ordered separately. Specify "Silhouette Extension

Brackets".

Mount the brackets to the wall, making sure they are level and vertically

plumb. Installer must insure fasteners (not included) are of adequate strength

and suitable for chosen mounting surface.

Attach hanging bracket to wall bracket as shown. Attach (1) "Z" Clip (supplied

with screen) to hanging bracket as shown.

Engage the lip on back of screen case with lip of "Z" Clip and gently pull down

to fully engage case to brackets. Screw in #10-16 x ½" screw on each bracket

to lock screen case in place (see below).

CB ¼"-20 x 1¾" Z Keg,

Flat Washer,

¼"-20 Nylock Nut

Hanging

Bracket

#10-24 x ½"

Screw,

Nylock Nut

Z Clip

Removing Case Fascia

Case fascia is removable to access roller assembly. To remove fascia, depress

outward the spring lip located inside lower front corner of screen case and

pull lower corner of fascia outward. Repeat this at right end of case. Support

fascia from center and rotate lower front edge upward approximately 40° to

disengage the Roll-Lok hinge at the top front of screen case. Fascia can now

be com plete ly removed from case.

To install fascia, generally reverse instructions above making sure the Roll-

Lok hinge is completely engaged before rotating fascia down towards the

closed position. Depress spring clips outward, push lower corners of fascia

inward until lips of spring clips hook behind fascia.

Please Note: Be sure the clips are completely up against

the ends of the fascia.

#10-16 x ½"

Screw

www.draperinc.com

Electrical Con nec tions

Screen operates on 220 V AC, 50 Hz., 1 ph current.

Junction box is located at left end of screen. It is accessible through front of

screen case after fascia is removed. (See instructions above for removing

fascia.) Electrical supply wires can enter through the back or top of case. For

top entry, remove plug from top conduit hole and snap plug into hole on back

side of case.

Junction box contains terminal strip (wiring diagram on page four).

If optional low voltage control or video interface control is speciﬁ ed and factory

installed, please refer to wiring diagram on page three.

Wall or ceiling electrical box should be installed so as to be fully con cealed by

screen case after installation.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is con nect ed.

Operation

Before operating screen, remove any shipping brackets or tape securing fabric

and dowel to the roller. If viewing surface is hanging out of the case 20 to 23

cm, tape has probably been broken by rough handling in shipment, allowing

surface to "unwrap" one turn off the roller. Manually wrap fabric back around

the roller without turning the roller itself.

When screen is ﬁ rst op er at ed, be cau tious! Cy cle unit down and up sev er al

times to con ﬁ rm sat is fac to ry operation.

220V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

220V MULTIPLE STATION CONTROL—(Not CE Approved) Switches are

similar in appearance to 220V Single Station Control. Screen stops when

switch is released and may be restarted in either direction. Factory adjusted

limit switches stop screen automatically when fully up or fully down.

24V MULTIPLE STATION CONTROL—Three-button UP-STOP-DOWN

switches stop at any point desired, operate in any sequence. Factory adjusted

limit switches automatically stop screen when fully up or fully down. Installer

should incorporate an all-pole disconnect in the ﬁ xed wiring.

220V & 12V VIDEO INTERFACE CONTROL—(Not CE Approved) Allows

screen to be controlled by a trigger signal—when the signal comes on, the

screen descends automatically. Two versions: Model VIC220 integrates screen

operation with a DRAPER video projector lift or a video projector or tuner with

a 220V switch outlet. Model VIC12 interfaces with a 12V switch outlet. Both

available with an override switch (VIC–OS), permitting independent operation.

VIC–OS not available with factory installed VIC220 & VIC12.

KEY OPERATED SWITCH ING—(Not CE Approved) Two kinds of key-oper-

ated switch es are op tion al ly available with this unit.

➀ The key-operated power supply switch controls power to the screen and

switches. When it is "off", the switches will not operate screen.

Key may be removed from the switch in either "on" or "off" position.

➁ A three-position key switch permits the screen to be op er at ed directly by

key. In this case, the screen's operator must always have a key.

RS232/Ethernet—Serial communication and network communication option-

ally available with wall switches, RF or IR remote.

(765) 987-7999

Page 2 of 4