- ページ 2

投影スクリーン Draper Series EのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Series E 4 ページ。 Electric projection screen
Draper Series E にも：取付・取扱説明書 (4 ページ)

ページを印刷する

Ultimate Access Series E & V by Draper

motorized Roller/Fabric Installation

1 The bottom access panel and trap door must be removed first.

2 The motor end mounting bracket has a metal bracket

with snap ring for accepting motor head. Back out the

two set screws in bracket until they are flush with top

side of bracket.

3 To engage the motor end bracket flange above the

two channels in the top of the screen housing, rotate

the bracket approximately 45° counterclockwise to

allow the top surface of the motor bracket to rest flat

against the top inside of the housing.

4 Rotating the bracket clockwise until it is engaged with

the channels, slide it along the length of the housing

against the electrical junction box.

5 Engage idler end bracket (rectangular

mounting pad) in the same manner as

motor end bracket and slide it toward the

opposite end of the screen housing.

Do not tighten set screws on this bracket

until the roller/fabric assembly is

installed, and centered in case.

Note: Step 6 requires two people to perform safely.

6 Locate the black washer and retaining clips attached to the instruction sheet.

Raise the roller/fabric assembly up into the screen housing and engage the

head of the motor completely into the motor mounting

bracket, making sure the limit switch adjusting knobs are

visible from the bottom of the screen housing (see fig. 6).

If snap ring is provided, make sure the snap ring engages with

the motor. If retaining clip is provided instead, install to lock

motor end in place.

7 While supporting the idler end of the roller, slide the idler end

mounting bracket toward the roller. Insert the roller pin into the

nylon bushing on the idler end mounting bracket.

8 The roller idler pin needs to go through the idler bracket far

enough to allow the washer and retaining clip to be reinstalled

on the pin.

CAUTION: Failure to replace the washer and retaining clip could

result in the separation of the roller from the brackets.

9 The roller/fabric assembly and roller brackets may need to be slid left or right in

the mounting channel of case to center fabric within screen case.

10 Securely tighten the set screws on roller mounting brackets.

11 Connect the electrical plug from the motor to the mating socket on the junction box.

12 Reinstall the bottom access panel as previously described.

motorized Roller/Fabric Removal

Reverse the instructions above "Motorized Roller/Fabric Installation" for removal of

the unit.

Operation

When screen is first operated, be cautious! Cycle unit down and up several times

to confirm satisfactory operation. Be prepared to cut POwER if necessary.

110-120V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

110-120V MULTIPLE STATION CONTROL—Switches are similar in appearance

to 110-120V Single Station Control. Screen stops when switch is released and

may be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully up or fully down.

24V CONTROL—Three-button UP-STOP-DOWN switches stop at any point

desired, operate in any sequence. Factory adjusted limit switches automatically

stop screen when fully up or fully down. Installer should incorporate an all-pole

disconnect in the fixed wiring available with RF or IR remote.

110-120V & 12V VIDEO INTERfACE CONTROL—Allows screen to be controlled

by trigger signal—when the signal comes on, the screen descends automatically.

Two versions: Model VIC115 integrates screen operation with a Draper video

projector lift or a video projector or tuner with a 110-120V switched outlet. Model

VIC12 interfaces with a 12V switched outlet. Both available with an override switch

(VIC–OS), permitting independent operation. VIC–OS not available with factory

installed VIC115 & VIC12.

KEY OPERATED SWITCHING—Two kinds of key-operated switches are

optionally available with this unit. 1 The key-operated power supply switch controls

power to the screen and switches. When it is "off", the switches will not operate

screen. Key may be removed from the switch in either "on" or "off" position.

2 A three-position key switch permits the screen to be operated directly by key.

In this case, the screen's operator must always have a key.

RS232/ETHERNET—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Figure

Idler end roller

mounting bracket

Washer

Retaining

Clip

Roller Assembly

Motor End

Set Screws

Mounting

Bracket

Motor End

Retaining Clip

Figure

www.draperinc.com

Limit Adjustments

Please Note: Screen limits are factory set for optimum performance of

the screen. A procedure is outlined below for minor tweaks, but any

adjustment of these limits may negatively affect the flatness of the

screen surface and could also void the warranty. Please check with

Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting

limit switches.

The motor limit screws are normally located on the audience left of screen roller.

"DOwN" LImIT ADjUSTmENT

To Reduce Screen Drop

1 Raise screen surface about 1' above desired setting and turn off.

2 Turn the WHITE/DOWN limit screw clockwise (three screw turns = ½ roller

revolution).

3 Test by running screen down and repeat steps 1 and 2 until desired position

is reached.

To Increase Screen Drop

1 Run screen to the down limit.

2 With the down switch on, turn the WHITE/DOWN limit screw counter-

clockwise (3 turns of screw equals ½ roller revolution) to increase drop.

3 Test by running screen up about 1' and back down to new down limit.

4 Repeat steps 2 and 3 until desired position is reached.

"UP" LImIT ADjUSTmENT

Screen is Running Too Far Up

1 Lower screen surface about 1' below desired setting and turn off.

2 Turn the YELLOW/UP limit screw clockwise (three screw turns = ½ roller

revolution).

3 Test by running screen up.

4 Repeat steps 1 through 3 until desired position is reached.

Screen Needs to Run Up more

1 Run screen down about 1' and turn off.

2 With the up switch on, turn the YELLOW/UP limit screw counterclockwise

(three turns of screw = ½ roller revolution).

3 Repeat steps 1 and 2 until desired position is reached.

CAUTION: Do NOT allow the dowel to wrap up over the roller when

the screen is running up! This could damage the screen.

Tab-Tension Adjustment Procedure for Ultimate Access/Series V

Draper's Tab-Tensioning System is factory-set, and under normal circumstances

will not require field adjustment. If, however, you notice wrinkles, waves or other

indications that the tensioning cables need to be adjusted, follow the procedure below.

1 Determine which side requires adjustment.

2 Secure dowel with one hand.

3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw

and slowly turn CLOCKWISE TO INCREASE tension, or

COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in

60° turn increments. Adjust only one increment (60° turn) at a time.

TENSIONING

CABLE

Figure

ADJUSTMENT

SCREW

DOWEL

4 If problem is not corrected, leave screen in position for 24 hours to allow

surface material to stretch into position.

5 If problem still is not corrected, repeat steps 2 and 3.

(765) 987-7999

Page 2 of 4

TENSIONING

CABLE

ADJUSTMENT

SCREW

DOWEL